115 En, Remote control | Yamaha YSP-40D specification

Troubleshooting

■	Remote control

	Problem	Cause	Remedy	See
	Problem	Cause	Remedy	page
				page

The remote control does not		Wrong distance or angle.	The remote control functions within a	29
work and/or function			maximum range of 6 m (20 ft) and no more
properly.			than 45 degrees off-axis from the front
			panel.

		Direct sunlight or lighting (from an inverter	Reposition this unit.	—
		type of fluorescent lamp, etc.) is striking the
		remote control sensor of this unit.

		The batteries are weak.	Replace all batteries.	29

Cannot operate external		The external component you want to operate	Press INPUT on the front panel or the input	44
components with the remote		is not selected as the input source.	selector buttons on the remote control to
control of this unit.			select the external component you want to
			operate.

		The remote control code was not correctly	Set the remote control code correctly or try	107
		set.	another code for the same manufacturer
			using the “List of remote control codes” at
			the end of this manual.

		Even if the remote control code is correctly	Use the remote control supplied with the	—
		set, there are some models that do not	external component.
		respond to the remote control.

The cursor buttons do not		The operation mode selector was	Set the operation mode selector to YSP.	—
work during SET MENU		unwantedly set to TV/AV.
operation.

Cannot use the My Beam		Wrong distance or angle.	The remote control functions within a	29
auto-adjust function.			maximum range of 6 m (20 ft) and no more
			than 45 degrees off-axis from the front
			panel.

■	HDMI

	Error message	Cause	Remedy	See
	Error message	Cause	Remedy	page
				page

Device Error		The number of the connected HDMI	Reduce the number of the connected HDMI	—
		components exceeds the limit.	components.

HDCP Error		HDCP authentication failed.	Check that the connected HDMI	—
			components support the HDCP copy
			protection standards.

Out of Resolution		The resolution of the HDMI output signals	Adjust UP-SCALING.	91
		exceeds the limit allowed by your TV.

INFORMATION	ADDITIONAL


English

115 En

Image 117

Yamaha YSP-40D owner manual 115 En, Remote control

Contents

YSP-40D For U.K. Customers Contents Overview Features Features Using this manual Supplied accessories Remote control ⋅1OSD* video pin cable ⋅1 Yellow Front panel Controls and functionsInput STANDBY/ON Front panel display Rear panel 10 En 11 En Remote control 12 En Search 13 EnNumeric buttons Memory Before installing this unit InstallationInstalling this unit 14 En Installation examples 15 EnExample Using a stand Using a metal wall bracketUsing a rack 16 En 17 En Connections 18 En 19 En Connections using Hdmi cablesRear panel of this unit DVD player/recorder 20 En Connecting a TV 21 En Connecting a DVD player/recorder Connecting a digital satellite tuner or a cable TV tuner Video signal to the TV22 En 23 En Connecting a digital airwave tuner 24 En Connecting a portable audio playerMm stereo mini plug cable Front panel of this unit Connecting other external components 25 EnDigital Connecting a subwoofer 26 EnMonaural Input Subwoofer About the RS-232C/IR-OUT/IR in terminals Connecting the DAB antenna27 En Indoor DAB antenna supplied Connecting the AC power supply cable 28 EnTo the AC wall outlet Operation range of the remote control Installing batteries in the remote controlClose the battery cover Getting started Press STANDBY/ON again to set this unit to the standby mode Press STANDBY/ON to turn on the power of this unit30 En Turn on the power of your TV Using SET MenuSET Menu Displaying the OSD on-screen display 32 En Flow chart of SET Menu Press / to select Language SETUP, and press Enter Language SetupChanging OSD language 33 En Flow chart of Auto Setup Auto Setup IntelliBeam34 En Beam optimization Sound optimization Press STANDBY/ON to turn off the power of this unit Installing the IntelliBeam microphone35 En Sofa 36 En Using Auto Setup IntelliBeamAssembling the supplied cardboard Microphone stand Center line Set the operation mode selector to YSP Auto SetupPress / to select Auto Setup and press Enter 37 En Auto Setup Start 38 EnBEAM+SOUND Optimz 39 En Show ResultCheck that the following screen is displayed on your TV Example Before the Auto Setup procedure starts Error messages for Auto SetupWhile the Auto Setup procedure is in progress 40 En Saving settings Using the system memory2MEMORY Save Memory 42 En Loading settingsPress Enter again Press / to select Memory and press 43 En 1MEMORY LoadPress / to select Load and press Press Enter again Press / to select MEMORY1 Playback Remote control operationsSelecting the input source 44 En Playing back sources Turn on the power of your DVD player45 En Press DVD to select DVD as the input source Press Volume +/- to increase or decrease the volume level Adjusting the volume46 En Muting the sound DAB Digital Audio Broadcasting Service Audio signal and service informationAbout DAB 47 En 48 En Preparing the DAB tuningPress k / n / l / h to start the initial scan Operation 49 En DAB tuning 3b Use the numeric buttons to enter a preset number 50 EnAppears on the front panel display Preset tuning 2b Use the numeric buttons to enter a preset service number51 En DAB service information DAB Information52 En DAB Menu Accessing DAB Menu53 En Selective initial scan 54 En Press / to switch to another channel labelPress Enter to confirm your selection Press once 55 En Press / to switch between Auto and OFFPress twice Function Press three times Press four times 56 En Connection Controlling iPod Using iPod57 En Yamaha iPod universal dock such as YDS-10, sold separately Controlling iPod in the Menu Browse Mode Controlling iPod in the Simple Remote ModePress DISPLAY, and display the menu browse mode 58 En 59 En Settings parameters Shuffle ShuffleAn example of the information display during playback Repeat Repeat Beam Enjoying surround sound60 En Press 5BEAM to select 5 Beam Stereo plus 3 Beam My Surround61 En Input channel indicators Decoder indicators62 En Surround modes and recommended sources Enjoying 2-channel sources Surround sound63 En 64 En Press Volume +/- to adjust the volume levelSelect the TV channel you want to watch Press TV When Dolby Pro Logic II Music is selected Adjusting surround mode parametersWhen DTS Neo6 Music is selected 65 En Enjoying stereo sound Channel stereo playback66 En Playing back sound clearly My Beam Using auto-adjust function67 En Press and hold MY Beam for more than two seconds Press / while MY Beam is displayed to adjust the beam angle Using manual-adjust function68 En Press MY Beam What is a sound field? Using sound field programs69 En Elements of a sound field Sound field program descriptions 70 En 71 En Cinema DSP programsMusic programs Press Music to select the music Cinema DSP program Movie programs 72 EnSports program Press Movie to select the movie Cinema DSP program 73 En Adjusting Cinema DSP effect levelsTurning off Cinema DSP programs Press OFF to turn off the Cinema DSP programs Using the music enhancer 74 EnPress Enhancer to select the Music Enhancer NIGHTMUSIC, or TV Equal Volume is Press / to adjust the effect level75 En Compression while Nightcinema 76 En Using the sleep timer Canceling the sleep timer 77 EnDisappears Displaying the input source information Input signal Indicator Sampling Frequency78 En Press Display 79 En Using the Hdmi control feature Sound Menu 80 EnBeam Menu Input Menu Manual Setup Using Manual Setup81 En Installed Position Installed position of this unit Setting parameters2BEAM Menu 82 En Installed Height Installed height of this unit Beam Adjustment Beam adjustment83 En Listening position from the unit Room width Room length Horizontal Angle Horizontal angle 84 EnVertical Angle Vertical angle Beam Travel Length Beam travel length Focal Length Focal length 85 EnTreble Gain Treble gain Front left channel Cimage Location 1SOUND MenuAtone Control Bsubwoofer SET Cmute Level Daudio DelayEroom EQ 87 En 88 En 3INPUT MenuTruBass Input Assignment Input assignment Input Mode Input mode Binput Mode89 En Input Trim Input trim Dinput Rename Hdmi SET Hdmi settingsEhdmi SET 90 En Video Info Video information 91 EnUP-SCALING Hdmi up-scaling Aspect Ratio Hdmi aspect ratio 4DISPLAY Menu Front panel display settingsAF.DISPLAY SET 92 En Unit SET Unit settings OSD SET OSD settingsBosd SET Cunit SET Adjusting the audio balance Using the test tone94 En 95 En Using the audio output being played back 96 En 97 En Selecting the input modeAuto DTS Using the system parameters Adjusting the system parameters98 En Release Input on the front panel 99 En Press / to switch between Protect on and Protect OFF Setting the Turn on Volume Setting the MAX VolumePress / to adjust the maximum volume level 100 En Setting the Monitor Check Press / to adjust the initial volume level101 En Setting the Demo Mode Press / to switch between MON CHK YES and MON CHK Skip102 En Setting the Panel Input KEY Press / to switch between Demo on Demo OFF103 En Press / to switch between P.INPUT on P.INPUT OFF Disabling the front panel keys104 En Setting the Factory Preset Press / to switch between F.PANEL on and F.PANEL OFF105 En 106 En Press / to switch between Preset Reset and Preset Cancel Setting remote control codes Remote control features107 En Code SET 108 En Controlling other componentsOperating your TV TV INPUT1 Operating your DVD player/recorder 109 EnOperating your STB CATV/Satellite tuner Operation buttons for DVD players 110 En Operating your VCROperation buttons for VCR Setting macros for the TV with the tuning capability Using the TV macroPress Enter to confirm the macro setting 111 En Canceling the macros Setting macros for the TV without the tuning capability112 En Operating macros Troubleshooting 113 EnGeneral 114 En 115 En Remote control IPod 116 En 117 En Glossary LFE 0.1-channel 118 EnPCM Linear PCM SRS TruBass DAB frequency table 119 EnBand Frequency Channel label Index 120 EnNumerics 121 En Specifications Conditions 122 En VCR List of remote control codesDVD Player Cable TV Tuner 834 Satellite Tuner All rights reserved Audio connection Items used for connections and operations This guide About the IntelliBeam microphone About the room environmentSubwoofer