Show Result, 39 En, Example, ← Flashes | Yamaha YSP-40D instruction

8Check that the following screen is displayed on your TV.

The results of the AUTO SETUP procedure are displayed on your TV.

Example 1

SHOW RESULT

MEASUREMENT COMPLETE

← Flashes

BEAM MODE :5 BEAM

SUBWOOFER :NOT APPLICABLE

[ENTER]:Save set-up. [RETURN]:Do not save set-up.

Example 2

SHOW RESULT

MEASUREMENT COMPLETE

← Flashes

ENVIRONMENT CHECK[FAILED]

BEAM MODE :5 BEAM

SUBWOOFER :YES

[ENTER]:Save set-up. [RETURN]:Do not save set-up.

y

•If “ENVIRONMENT CHECK [FAILED]” is displayed, we recommend running the AUTO SETUP procedure again. For details, see step 9.

•If “SUBWOOFER : NOT APPLICABLE” is displayed even though a subwoofer is connected to this unit, increase the volume level of the subwoofer and run the AUTO SETUP procedure again.

•Depending on the environment of your listening room, the beam angle of front left and right, and surround left and right may be set to the same value even if

“5 BEAM” is displayed as a result.

AUTO SETUP (IntelliBeam)

9Press ENTER to confirm the results or press RETURN to cancel the results.

The following screen is displayed for two seconds and then disappears from your TV.

AUTO SETUP COMPLETE

Please remove the MIC from

ENTERthe YSP and the listening position.

If “ENVIRONMENT CHECK [FAILED]” is displayed in step 8, the following screen is displayed after pressing ENTER. In this case, see ERROR E-1 in “Error messages for AUTO SETUP” on page 40. Press ENTER to exit AUTO SETUP and then run the procedure again from step 3.

AUTO SETUP COMPLETE

Your YSP unit may not be set up correctly.

We recommend you try again.

Please press [ENTER] key to exit.

10Disconnect the IntelliBeam microphone from the INTELLIBEAM MIC jack on the front panel.

AUX 3 INTELLIBEAM MIC

SETUP

y

If you want to save and load settings, see “Using the system memory” on page 41.

English

39 En

Image 41

Yamaha YSP-40D owner manual Show Result, 39 En, Check that the following screen is displayed on your TV, Example, ← Flashes

Contents

YSP-40D For U.K. Customers Contents Overview Features Features Using this manual OSD* video pin cable ⋅1 Yellow Supplied accessoriesRemote control ⋅1 Front panel Controls and functionsInput STANDBY/ON Front panel display Rear panel 10 En 11 En Remote control 12 En Search 13 EnNumeric buttons Memory Before installing this unit InstallationInstalling this unit 14 En Example Installation examples15 En Using a stand Using a metal wall bracketUsing a rack 16 En 17 En Connections 18 En 19 En Connections using Hdmi cablesRear panel of this unit DVD player/recorder 20 En Connecting a TV 21 En Connecting a DVD player/recorder 22 En Connecting a digital satellite tuner or a cable TV tunerVideo signal to the TV 23 En Connecting a digital airwave tuner 24 En Connecting a portable audio playerMm stereo mini plug cable Front panel of this unit Digital Connecting other external components25 En Monaural Input Subwoofer Connecting a subwoofer26 En About the RS-232C/IR-OUT/IR in terminals Connecting the DAB antenna27 En Indoor DAB antenna supplied To the AC wall outlet Connecting the AC power supply cable28 En Operation range of the remote control Installing batteries in the remote controlClose the battery cover Getting started 30 En Press STANDBY/ON again to set this unit to the standby modePress STANDBY/ON to turn on the power of this unit Turn on the power of your TV Using SET MenuSET Menu Displaying the OSD on-screen display 32 En Flow chart of SET Menu Press / to select Language SETUP, and press Enter Language SetupChanging OSD language 33 En Flow chart of Auto Setup Auto Setup IntelliBeam34 En Beam optimization Sound optimization Press STANDBY/ON to turn off the power of this unit Installing the IntelliBeam microphone35 En Sofa 36 En Using Auto Setup IntelliBeamAssembling the supplied cardboard Microphone stand Center line Set the operation mode selector to YSP Auto SetupPress / to select Auto Setup and press Enter 37 En BEAM+SOUND Optimz Auto Setup Start38 En 39 En Show ResultCheck that the following screen is displayed on your TV Example Before the Auto Setup procedure starts Error messages for Auto SetupWhile the Auto Setup procedure is in progress 40 En Saving settings Using the system memory2MEMORY Save Memory 42 En Loading settingsPress Enter again Press / to select Memory and press 43 En 1MEMORY LoadPress / to select Load and press Press Enter again Press / to select MEMORY1 Playback Remote control operationsSelecting the input source 44 En Playing back sources Turn on the power of your DVD player45 En Press DVD to select DVD as the input source Press Volume +/- to increase or decrease the volume level Adjusting the volume46 En Muting the sound DAB Digital Audio Broadcasting Service Audio signal and service informationAbout DAB 47 En 48 En Preparing the DAB tuningPress k / n / l / h to start the initial scan Operation 49 En DAB tuning Appears on the front panel display 3b Use the numeric buttons to enter a preset number50 En 51 En Preset tuning2b Use the numeric buttons to enter a preset service number 52 En DAB service informationDAB Information DAB Menu Accessing DAB Menu53 En Selective initial scan 54 En Press / to switch to another channel labelPress Enter to confirm your selection Press once 55 En Press / to switch between Auto and OFFPress twice Function Press three times Press four times 56 En Connection Controlling iPod Using iPod57 En Yamaha iPod universal dock such as YDS-10, sold separately Controlling iPod in the Menu Browse Mode Controlling iPod in the Simple Remote ModePress DISPLAY, and display the menu browse mode 58 En 59 En Settings parameters Shuffle ShuffleAn example of the information display during playback Repeat Repeat Beam Enjoying surround sound60 En Press 5BEAM to select 5 Beam 61 En Stereo plus 3 BeamMy Surround Input channel indicators Decoder indicators62 En Surround modes and recommended sources 63 En Enjoying 2-channel sourcesSurround sound 64 En Press Volume +/- to adjust the volume levelSelect the TV channel you want to watch Press TV When Dolby Pro Logic II Music is selected Adjusting surround mode parametersWhen DTS Neo6 Music is selected 65 En 66 En Enjoying stereo soundChannel stereo playback Playing back sound clearly My Beam Using auto-adjust function67 En Press and hold MY Beam for more than two seconds Press / while MY Beam is displayed to adjust the beam angle Using manual-adjust function68 En Press MY Beam What is a sound field? Using sound field programs69 En Elements of a sound field Sound field program descriptions 70 En 71 En Cinema DSP programsMusic programs Press Music to select the music Cinema DSP program Movie programs 72 EnSports program Press Movie to select the movie Cinema DSP program 73 En Adjusting Cinema DSP effect levelsTurning off Cinema DSP programs Press OFF to turn off the Cinema DSP programs Press Enhancer to select the Music Enhancer Using the music enhancer74 En NIGHTMUSIC, or TV Equal Volume is Press / to adjust the effect level75 En Compression while Nightcinema 76 En Using the sleep timer Disappears Canceling the sleep timer77 En Displaying the input source information Input signal Indicator Sampling Frequency78 En Press Display 79 En Using the Hdmi control feature Sound Menu 80 EnBeam Menu Input Menu 81 En Manual SetupUsing Manual Setup Installed Position Installed position of this unit Setting parameters2BEAM Menu 82 En Installed Height Installed height of this unit Beam Adjustment Beam adjustment83 En Listening position from the unit Room width Room length Horizontal Angle Horizontal angle 84 EnVertical Angle Vertical angle Beam Travel Length Beam travel length Focal Length Focal length 85 EnTreble Gain Treble gain Front left channel Cimage Location 1SOUND MenuAtone Control Bsubwoofer SET Cmute Level Daudio DelayEroom EQ 87 En 88 En 3INPUT MenuTruBass Input Assignment Input assignment Input Mode Input mode Binput Mode89 En Input Trim Input trim Dinput Rename Hdmi SET Hdmi settingsEhdmi SET 90 En Video Info Video information 91 EnUP-SCALING Hdmi up-scaling Aspect Ratio Hdmi aspect ratio 4DISPLAY Menu Front panel display settingsAF.DISPLAY SET 92 En Unit SET Unit settings OSD SET OSD settingsBosd SET Cunit SET 94 En Adjusting the audio balanceUsing the test tone 95 En Using the audio output being played back 96 En 97 En Selecting the input modeAuto DTS Using the system parameters Adjusting the system parameters98 En Release Input on the front panel 99 En Press / to switch between Protect on and Protect OFF Setting the Turn on Volume Setting the MAX VolumePress / to adjust the maximum volume level 100 En 101 En Setting the Monitor CheckPress / to adjust the initial volume level 102 En Setting the Demo ModePress / to switch between MON CHK YES and MON CHK Skip 103 En Setting the Panel Input KEYPress / to switch between Demo on Demo OFF 104 En Press / to switch between P.INPUT on P.INPUT OFFDisabling the front panel keys 105 En Setting the Factory PresetPress / to switch between F.PANEL on and F.PANEL OFF 106 En Press / to switch between Preset Reset and Preset Cancel Setting remote control codes Remote control features107 En Code SET 108 En Controlling other componentsOperating your TV TV INPUT1 Operating your DVD player/recorder 109 EnOperating your STB CATV/Satellite tuner Operation buttons for DVD players Operation buttons for VCR 110 EnOperating your VCR Setting macros for the TV with the tuning capability Using the TV macroPress Enter to confirm the macro setting 111 En Canceling the macros Setting macros for the TV without the tuning capability112 En Operating macros General Troubleshooting113 En 114 En 115 En Remote control IPod 116 En 117 En Glossary LFE 0.1-channel 118 EnPCM Linear PCM SRS TruBass Band Frequency Channel label DAB frequency table119 En Numerics Index120 En 121 En Specifications Conditions 122 En VCR List of remote control codesDVD Player Cable TV Tuner 834 Satellite Tuner All rights reserved Audio connection Items used for connections and operations This guide Subwoofer About the IntelliBeam microphoneAbout the room environment