RIDGID RD8000 Assembly, Loose Parts List, Unpacking, Installing Legs, Installing the wheels

Page 11

ASSEMBLY

WARNING:

Do not attempt to operate the generator until assembly is complete. Failure to comply could result in possible serious personal injury.

LOOSE PARTS LIST

See Figure 4.

The following items are included with the generator:

Key

 

 

No.

Description

Qty.

1

Axle

2

2

Wheel

2

3

Flat Washer (5/8 in.)

2

4

Hitch Pin

2

5

Screw (1/4-20 x 2 in., Hex Hd.)

4

6

Flat Washer (1/4 in.)

6

7

Leg with Rubber Foot

2

8

Nut (1/4-20 Self-Locking Nut)

6

9

Extension Cord, 25 ft

1

10

Engine Lubricant

1

11

Screw (1/4-20 x 1 in., Hex Hd.)

2

12

Key

1

 

Operator’s Manual (not shown)

1

UNPACKING

This product requires assembly.

Carefully cut the box down the sides then remove the machine and any accessories from the box. Make sure that all items listed in the packing list are included.

NOTE: This machine is heavy and requires a minimum of two people to lift. To avoid back injury, lift with your legs and not your back.

WARNING:

Do not use this product if any parts on the Loose Parts List are already assembled to your product when you unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in serious personal injury.

Inspect the product carefully to make sure no damage occurred during shipping.

Do not discard the packing material until you have carefully­ inspected and satisfactorily operated the product­.

If any parts are damaged or missing, please call 1-866-539-1710, for assistance.

WARNING:

If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

WARNING:

Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

NOTE:  Do not put fuel or lubricant in the generator before installing the legs and wheels.

installing LEGS

See Figure 5.

Locate the following items:

2 legs with rubber feet

6 flat washers

6 lock nuts

4 screws (2 in.)

2 screws (1 in.)

Raise the front end of the generator, where the engine is located, high enough to gain access to the frame bottom; securely position props underneath to support.

Position a leg over the holes on each side of the frame support.

Insert each 2 in. screw through a flat washer and insert the screws through the two holes in the frame and the leg.

Fasten the screws by installing a self-locking nut over each screw on the inside of the frame. Tighten the nut securely.

Insert a 1 in. screw through a flat washer, the hole in the frame crossbar, and then through the hole in the leg tab. Install a self-locking nut and tighten to secure.

Repeat with remaining leg.

installing the wheels

See Figure 6.

Wheels are provided to assist in moving the generator to the desired location and should be installed on the side opposite the recoil starter.

Locate the following items: 2 axles

2 washers (5/8 in.)

2 hitch pins

2 wheels

11 — English

Image 11
Contents AVERTISSEMENT  Portable GeneratorRD8000 / RD80011 Series / Série / Serie Neutral Bonded to FrameIntroduction Table of ContentsKill YOU in Minutes Important safety instructionsSpecific Safety Rules Symbol Signal Meaning SymbolsHot Surface warning Safety LabelsElectrical SymbolsSee Figure Ground fault circuit interrupterElectric motor loads Extension cordGenerator Capacity Power ManagementKnow Your Generator FeaturesProduct Specifications Installing the wheels AssemblyLoose Parts List Installing LegsRemovable Control Panel AssemblyConnecting battery Installing a Wall Mount for the removable control panelRaising and Lowering the Handle OperationApplications Before Operating the UnitGenSmart Digital Display Using fuel stabilizerChecking/adding fuel Oxygenated FuelsElectric Start Generator Control PanelMoving the Generator Lifting the GeneratorTo stop the engine under normal operating conditions Starting the engineStopping the engine General Maintenance MaintenanceTransporting Cleaning the Exhaust Port and MUFFLER­Spark arrestor Draining fuel tank/carburetorStorage time Prior to storing MaintenanceMaintenance Schedule StorageProblem Possible Cause Solution TroubleshootingWhat is not Covered WarrantyYear Limited Warranty What is Covered Under the 3 Year Limited WarrantyWarranty Periods Limited Manufacturer’s Warranty from Subaru RobinEvaporative Emission Control Warranty Statement Arrière Table DES MatièresMise À LA Terre DU Générateur Conserver CES Instructions Instructions Importantes Concernant LA SécuritéAdvertissement Règles de sécurité particulières Avertissement SymbolesSymbole Signal Signification SÉCURITÉ­ Autocollants DEMise À LA Terre Avertissement Caractéristiques électriquesAvertissement Concernant LE Carburant Avertissement Concernant Le lubrifiant MoteurVoir la figure Charges du moteur électriqueCordon Prolongateur Disjoncteur de fuite à la terreGestion DE L’ÉNERGIE Capacité du générateurCaractéristiques Déballage AssemblageAvertissement LISTe deS PIÈceS dÉTachÉeVoir las figures 9 et Installation DES RouesPanneau de commande amovible Connexion d’une pileVÉRIFICATION/AJOUT de lubrifiant UtilisationAvant D’UTILISER L’UNITÉ Rélever ET Abaisser LA PoignéeCarburants Oxygénés VÉRIFICATION/AJOUT DE CarburantUtilisation DE Stabilisateur DE Carburant Soulever LA Génératrice Panneau de commande de la générateurDéplacement du génératrice Arrêt DU Moteur Démarrage ÉlectriqueMise EN Marche DU Moteur Entretien DE LA Bougie EntretienEntretien Général INSPECTION/NETTOYAGE DU Filtre À AIRTransport Nettoyage DE L’ORIFICE D’ÉCHAPPEMENT ET DU SilencieuxPARE-ÉTINCELLES Vidange DU Réservoir DE CARBURANT/ CarburateurCalendrier D’ENTRETIEN RemisageDépannage Problème Cause Possible SolutionCE QUI N’EST PAS Couvert Garantie Limitée DE Service DE 3 ANSGarantie CE QUI EST Couvert PAR LA Garantie Limitée DE Trois ANSPériodes DE Garantie Garantie limitée de Subaru RobinResponsabilités DU Propriétaire Dans LE Cadre DE LA Garantie Pág. posterior Índice DE ContenidoIntroducción Peligro Conexión a tierra del generadorGuarde estas instrucciones Instrucciones de seguridad importantesPeligro AdvertenciaReglas DE Seguridad Específicas Símbolo Señal Significado SÍMBOLoSPeligro PrecauciónAdvertencia de Superficie caliente Etiquetas DE SeguridadAdvertencia acerca de la conexión a tierra Aspectos eléctricosAdvertencia de combustible Advertencia del lubricante de motorPara efectuar una prueba Cargas de motores eléctricosCordón de extensión Vea la figuraCapacidad del generador Administración DE LA PotenciaTanque DE Combustible CON Indicador DE Carga CaracterísticasEspecificaciones DEL Producto Familiarícese CON EL GeneradorInstalación de lAS patas ArmadoLIsTa DE pIEzas sUElTas DesempaquetadoPara quitar el panel de control desmontable del generador Instalación de las ruedasConexión DE LA Batería Panel de control desmontableLEvANTAR y BAjAR EL MANgO FuncionamientoAplicaciones Antes DE Accionar LA UnidadCombustibles Oxigenados Verificación y abastecimiento de combustibleUso de estabililzador de combustible­ Levantar EL Generador Panel de control generalTraslado el generador Apagado del motor Arranque eléctricoArranque del motor Mantenimiento General MantenimientoTransporte Limpieza DEL Orificio DE Escape Y DEL SilenciadorParachispas Drenaje del tanque del combustible y del carburadorPrograma DE Mantenimiento AlmacenamientoProblema Causa Posible Solución Corrección de problemasLO QUE no Está Cubierto GarantíaRidgid Generador Garantía DE lIMITADA DE 3 AñosMotor CON Garantía Limitada DE 3 Años Cobertura DE LA Garantía DEL Fabricante Información sobre servicio al consumidor Customer Service InformationService après-vente  RD8000/RD80011 Series / Série / SeriePage Iii Axle essieu, eje OFF Start Engine Switch Page Combustible Off arret, apagado Fi g

RD80011, RD8000 specifications

The RIDGID RD8000 and RD80011 represent a significant advancement in the world of underground utility locating. These versatile tools are designed to help professionals accurately detect and trace buried utilities, ensuring safe and efficient excavation and construction processes.

Both models are equipped with advanced signal processing technologies that enhance their ability to locate utilities, even in challenging environments. The RD8000 is renowned for its range of frequencies—typically offering up to five different transmission frequencies, allowing users to locate a variety of utility types including electric, gas, water, and telecommunications lines. This frequency versatility means that users can effectively cater to a wide spectrum of application needs, from residential projects to large-scale infrastructure work.

The RD80011 variant enhances these capabilities with added features aimed at improving user experience and precision. One standout feature is the built-in GPS technology, which allows for real-time mapping and locating of utilities, providing users with the ability to track locations directly on their devices. This integration streamlines the process of recording and reporting utility locations, fostering efficient workflow and reducing the risk of errors in documentation.

Additionally, both models boast an ergonomic design, featuring a lightweight build and intuitive controls that make them user-friendly. The display screen is bright and easy to read, featuring visual indicators that help convey critical information at a glance. The RD8000 and RD80011 utilize a rechargeable battery that ensures long-lasting power, giving users the confidence to tackle extended projects without the need to frequently replace batteries.

Another valuable characteristic is the built-in earphone jack, allowing for enhanced audio feedback and communication in noisy environments. Users can listen for specific tones corresponding to different utilities, which can aid in pinpointing the location with greater accuracy.

These RIDGID models also include advanced interference suppression technologies to minimize signal distortion from other nearby utilities, ensuring users receive clear and accurate data. This feature is particularly vital in complex urban settings where multiple utilities coexist in close proximity.

In summary, both the RIDGID RD8000 and RD80011 are designed with professional utility locators in mind, integrating advanced technologies and features that enhance detection capabilities, improve ease of use, and contribute to safer excavation practices.