RIDGID RD80011, RD8000 Démarrage Électrique, Mise EN Marche DU Moteur, Arrêt DU Moteur

Page 38

Utilisation

DÉMARRAGE ÉLECTRIQUE

Voir la figure 19.

Ce modèle de génératrice est offert avec des fonctions de démarrage électrique ou de démarrage à rappel. Évitez les démarragesprolongéscarilsrisquentd’endommagerlemoteur.

La pile fournie en est une de type rechargeable au plomb étanche d’une charge nominale de 12 volts pouvant fonctionner dans n’importe quelle position sans risque de fuite. Elle est conforme aux règlements relatifs aux piles hermétiques. Son format pratique est 30 pour cent plus compact que celui des piles traditionnelles.

NOTE : Les nouvelles génératrices sont expédiées avec les connexions de pile débranchées. Les bornes positive et négative doivent être branchées à la pile avant que la fonction de démarrage électrique puisse fonctionner.

Pour procéder à la connexion initiale d’une pile, consulter la section intitulée Connexion d’une pile.

ATTENTION :

Sur une surface à niveau, avec le moteur sur arrêt, vérifier le niveau d’huile avant chaque utilisation du générateur.

MISE EN MARCHE DU MOTEUR

Voir la figure 20.

NOTE : Si l’emplacement de générateur n’est pas à niveau, l’unité peut ne pas démarrer ou peut s’arrêter durant le fonctionnement.

Débrancher toutes les charges du générateur.

Ouvrir le robinet de carburant.

Écarter droit le levier d’étranglement à la position START (DÉMARRAGE).

NOTE : Si le moteur est chaud ou que la température est supérieure à 10 °C (50 °F), écarter gauche le levier d’étranglement sur la position RUN (MARCHE). La batterie a été expédiée dans un état de charge faible. Par conséquent, il peut être nécessaire de la charger avant d’être en mesure de faire démarrer la génératrice avec la clé d’interrupteur. Il est possible de mettre en marche la génératrice en tirant sur le lanceur. Une fois que la génératrice a été mise en marche, la charge de la batterie s’effectue pendant que l’unité fonctionne.

Tournez le clé de commutateur du moteur sur “ON”.

Tourner la clé de commutateur à la position « START » ou tirer la poignée de démarrage à rappel jusqu’à ce que le moteur démarre (6 fois maximum).

NOTE : Ne pas laisser la poignée repartir brusquement en arrière après le démarrage. La ramener doucement à sa place d’origine.

NOTE : La batterie a été expédiée dans un état de charge faible. Par conséquent, il peut être nécessaire de la charger avant d’être en mesure de faire démarrer la génératrice avec la clé d’interrupteur. Il est possible de mettre en marche la génératrice en tirant sur le lanceur. Une fois que la génératrice a été mise en marche, la charge de la batterie s’effectue pendant que l’unité fonctionne.

Laisser le moteur tourner pendant 30 secondes et mettre le levier d’étranglement sur RUN (MARCHE).

ARRÊT DU MOTEUR

Voir la figure 20.

Pour arrêter le moteur dans des conditions de fonctionnement normales :

Retirer toute charge du générateur.

Fermer le clé d’interrupteur sur ARRET ou maintenir le bouton enfoncé jusqu’à ce que le moteur s’arrête.

NOTE : Le générateur peut être passé tourner la clef de commutateur à de ou en appuyant et tenir le commutateur de moteur sur le tableau de commande avant fixe.

Mettre le robinet de carburant sur ARRET.

NOTE : S’il faut éteindre le moteur immédiatement, il est possible d’utiliser l’un ou l’autre des interrupteurs du moteur si le panneau de commande amovible est relié à l’unité. L’interrupteur de marche-arrêt provisoire sur le panneau de commande stationnaire peut servir d’interrupteur d’arrêt principal.

16 — Français

Image 38
Contents Neutral Bonded to Frame Portable GeneratorRD8000 / RD80011 Series / Série / Serie AVERTISSEMENT Table of Contents IntroductionImportant safety instructions Kill YOU in MinutesSpecific Safety Rules Symbols Symbol Signal MeaningSafety Labels Hot Surface warningSymbols ElectricalExtension cord Ground fault circuit interrupterElectric motor loads See FigurePower Management Generator CapacityKnow Your Generator FeaturesProduct Specifications Installing Legs AssemblyLoose Parts List Installing the wheelsInstalling a Wall Mount for the removable control panel AssemblyConnecting battery Removable Control PanelBefore Operating the Unit OperationApplications Raising and Lowering the HandleOxygenated Fuels Using fuel stabilizerChecking/adding fuel GenSmart Digital DisplayLifting the Generator Generator Control PanelMoving the Generator Electric StartTo stop the engine under normal operating conditions Starting the engineStopping the engine Maintenance General MaintenanceDraining fuel tank/carburetor Cleaning the Exhaust Port and MUFFLER­Spark arrestor TransportingStorage MaintenanceMaintenance Schedule Storage time Prior to storingTroubleshooting Problem Possible Cause SolutionWhat is Covered Under the 3 Year Limited Warranty WarrantyYear Limited Warranty What is not CoveredLimited Manufacturer’s Warranty from Subaru Robin Warranty PeriodsEvaporative Emission Control Warranty Statement Arrière Table DES MatièresMise À LA Terre DU Générateur Conserver CES Instructions Instructions Importantes Concernant LA SécuritéAdvertissement Règles de sécurité particulières Avertissement SymbolesSymbole Signal Signification Autocollants DE SÉCURITÉ­Avertissement Concernant Le lubrifiant Moteur Caractéristiques électriquesAvertissement Concernant LE Carburant Mise À LA Terre AvertissementDisjoncteur de fuite à la terre Charges du moteur électriqueCordon Prolongateur Voir la figureCapacité du générateur Gestion DE L’ÉNERGIECaractéristiques LISTe deS PIÈceS dÉTachÉe AssemblageAvertissement DéballageConnexion d’une pile Installation DES RouesPanneau de commande amovible Voir las figures 9 etRélever ET Abaisser LA Poignée UtilisationAvant D’UTILISER L’UNITÉ VÉRIFICATION/AJOUT de lubrifiantCarburants Oxygénés VÉRIFICATION/AJOUT DE CarburantUtilisation DE Stabilisateur DE Carburant Soulever LA Génératrice Panneau de commande de la générateurDéplacement du génératrice Arrêt DU Moteur Démarrage ÉlectriqueMise EN Marche DU Moteur INSPECTION/NETTOYAGE DU Filtre À AIR EntretienEntretien Général Entretien DE LA BougieVidange DU Réservoir DE CARBURANT/ Carburateur Nettoyage DE L’ORIFICE D’ÉCHAPPEMENT ET DU SilencieuxPARE-ÉTINCELLES TransportRemisage Calendrier D’ENTRETIENProblème Cause Possible Solution DépannageCE QUI EST Couvert PAR LA Garantie Limitée DE Trois ANS Garantie Limitée DE Service DE 3 ANSGarantie CE QUI N’EST PAS CouvertGarantie limitée de Subaru Robin Périodes DE GarantieResponsabilités DU Propriétaire Dans LE Cadre DE LA Garantie Peligro Conexión a tierra del generador Índice DE ContenidoIntroducción Pág. posteriorAdvertencia Instrucciones de seguridad importantesPeligro Guarde estas instruccionesReglas DE Seguridad Específicas Precaución SÍMBOLoSPeligro Símbolo Señal SignificadoEtiquetas DE Seguridad Advertencia de Superficie calienteAdvertencia del lubricante de motor Aspectos eléctricosAdvertencia de combustible Advertencia acerca de la conexión a tierraVea la figura Cargas de motores eléctricosCordón de extensión Para efectuar una pruebaAdministración DE LA Potencia Capacidad del generadorFamiliarícese CON EL Generador CaracterísticasEspecificaciones DEL Producto Tanque DE Combustible CON Indicador DE CargaDesempaquetado ArmadoLIsTa DE pIEzas sUElTas Instalación de lAS patasPanel de control desmontable Instalación de las ruedasConexión DE LA Batería Para quitar el panel de control desmontable del generadorAntes DE Accionar LA Unidad FuncionamientoAplicaciones LEvANTAR y BAjAR EL MANgOCombustibles Oxigenados Verificación y abastecimiento de combustibleUso de estabililzador de combustible­ Levantar EL Generador Panel de control generalTraslado el generador Apagado del motor Arranque eléctricoArranque del motor Mantenimiento Mantenimiento GeneralDrenaje del tanque del combustible y del carburador Limpieza DEL Orificio DE Escape Y DEL SilenciadorParachispas TransporteAlmacenamiento Programa DE MantenimientoCorrección de problemas Problema Causa Posible SoluciónGarantía DE lIMITADA DE 3 Años GarantíaRidgid Generador LO QUE no Está CubiertoMotor CON Garantía Limitada DE 3 Años Cobertura DE LA Garantía DEL Fabricante RD8000/RD80011 Series / Série / Serie Customer Service InformationService après-vente  Información sobre servicio al consumidorPage Iii Axle essieu, eje OFF Start Engine Switch Page Fi g Combustible Off arret, apagado

RD80011, RD8000 specifications

The RIDGID RD8000 and RD80011 represent a significant advancement in the world of underground utility locating. These versatile tools are designed to help professionals accurately detect and trace buried utilities, ensuring safe and efficient excavation and construction processes.

Both models are equipped with advanced signal processing technologies that enhance their ability to locate utilities, even in challenging environments. The RD8000 is renowned for its range of frequencies—typically offering up to five different transmission frequencies, allowing users to locate a variety of utility types including electric, gas, water, and telecommunications lines. This frequency versatility means that users can effectively cater to a wide spectrum of application needs, from residential projects to large-scale infrastructure work.

The RD80011 variant enhances these capabilities with added features aimed at improving user experience and precision. One standout feature is the built-in GPS technology, which allows for real-time mapping and locating of utilities, providing users with the ability to track locations directly on their devices. This integration streamlines the process of recording and reporting utility locations, fostering efficient workflow and reducing the risk of errors in documentation.

Additionally, both models boast an ergonomic design, featuring a lightweight build and intuitive controls that make them user-friendly. The display screen is bright and easy to read, featuring visual indicators that help convey critical information at a glance. The RD8000 and RD80011 utilize a rechargeable battery that ensures long-lasting power, giving users the confidence to tackle extended projects without the need to frequently replace batteries.

Another valuable characteristic is the built-in earphone jack, allowing for enhanced audio feedback and communication in noisy environments. Users can listen for specific tones corresponding to different utilities, which can aid in pinpointing the location with greater accuracy.

These RIDGID models also include advanced interference suppression technologies to minimize signal distortion from other nearby utilities, ensuring users receive clear and accurate data. This feature is particularly vital in complex urban settings where multiple utilities coexist in close proximity.

In summary, both the RIDGID RD8000 and RD80011 are designed with professional utility locators in mind, integrating advanced technologies and features that enhance detection capabilities, improve ease of use, and contribute to safer excavation practices.