Remington Power Tools 104317, PS1510A manual Saw Chain Tension Adjustment, Hand Guard

Page 11

Chain Saw Information

Saw Chain Tension Adjustment

WARNING: Unplug chain saw from power source before adjusting saw chain tension.

WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.

WARNING: Maintain proper chain tension always. A loose chain will in- crease the risk of kickback.Aloose chain may jump out of guide bar groove. This may injure operator and damage chain.A loose chain will cause chain, guide bar, and sprocket to wear rapidly.

Note: For pre-assembled models, the saw chain tension is properly set at factory. A new chain will stretch. Check new chain after frst few minutes of operation. Allow chain to cool down. Follow steps below to readjust saw chain tension.

1.Before adjusting chain, make sure guide bar nuts are only finger tight (see Figure 4). Also make sure adjusting block is in oval adjusting hole on guide bar (see Figures 4 and 5).

2.Turn adjusting screw clockwise. (see Figure 6). Note: There should be no gap between side links of chain and bottom of guide bar (see Figure 7).

3.Wearing protective gloves, move chain around guide bar. Chain should move freely. If chain does not move freely, loosen chain by turning adjusting screw counterclockwise.

4.After chain tension is correct, tighten guide bar nuts firmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kickback. This can also damage saw. Note: A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Read just chain tension.

Towards Guide Bar Nose

Front Hand Guard

 

 

Tapping

Cutting Edge

ENGLISH

Screw

Adjusting

Guide Bar

Saw Chain

 

Bolts

 

 

Mounting

 

 

Stand-Outs

Guide Bar

 

 

 

 

Hole

 

 

Guide Bar Nuts

 

 

Drive Sprocket

 

Figure 4 - Assembling Guide Bar, Chain, and

 

Hand Guard

 

 

Adjusting Block

Adjusting Plate

 

 

Adjusting

 

 

Screw

 

Sprocket Support

Figure 5 - Part Locations For Assembling Guide Bar

Figure 6 - Turning Adjusting Screw

Guide Bar Nuts

Guide Bar

Guide Bar

Gap

Correct Tension

Incorrect

Tension

Figure 7 - Saw Chain Adjustment

11

www.desatech.com

Image 11
Contents Models RPS2N1 104317, PS1510A Telescoping electric Chainsaw/polesawPara Ayuda Técnica Llame AL Call 1-800-626-2237 for Technical AssistanceContents While Operating Saw Important Safety InformationRead ALL Instructions Before Operating SawKickback Kickback Safety Devices On This Saw IMPORTANT Safety InformationMaintenance and Storage of Saw Saw Maintenance and Kickback SafetyUnpacking Pole Saw Trimming PrecautionsModels 104317, PS1510A Product IdentificationChain SAW All Models PolesawTrimming Pruning Process of cutting limbs from a living tree Chain SAW Terms and DefinitionsChain Saw HardwarE Chain Saw AssemblyImportant Do not clamp chain saw in vise during assembly Hand Guard Saw Chain Tension AdjustmentCutting with the Chain Saw Extension CordsOiling Chain Filling Oil TankBefore Felling a Tree Felling a Tree Cutting Down a TreeFelling Cut Felling Procedure Felling NotchEntire Length Of Log On Ground Limbing a TreeBucking a Log Trimming a Tree Pruning Log Supported On One EndLog Supported On Both Ends RPS2N1 Cutting with the Pole Saw Adjusting Pole Length RPS2N1Care of Guide Bar Cleaning and MaintenanceCleaning Saw Body Normal Guide Bar MaintenanceFiling Cutter Depth Gauges Sharpening Saw ChainItems Needed to Sharpen Chain Sharpening CuttersReplacement Parts And accessories Non-Warranty Service TroubleshootingRepair Service Warranty ServiceFactory Reconditioned Products Remington brand Electric Chain SAWLimited Warranties New ProductsModelo RPS2N1 104317, PS1510A Sierra Eléctrica DE Pértiga TelescópicaIntroducción ContentsAntes DE Utilizar LA Sierra Información Importante DE SeguridadAL Utilizar LA Sierra LEA Todas LAS InstruccionesEspañol Mantenimiento de la cadena y seguridad contra contragolpes ContragolpesMantenimiento Y Almacenamiento DE SU Sierra Eléctrica Desembalaje Precauciones Para Podar CON LA Sierra DE PértigaModelos 104317, PS1510A Identificación DEL ProductoSierra Eléctrica Sierra DE PértigaTérminos Y Definiciones DE LA Sierra DE Cadena Ensamblaje Información Sobre LA Sierra DE CadenaAccesorios DE LA Sierra DE Cadena Ajuste DE Tensión DE LA Cadena Serrada Important no USE aceite estándar para barra y cadenas LubricaciónCables DE Prolongación Lubricación DE LA CadenaAdvertencia Realización DE CortesTala DE UN Árbol Derribamiento de un árbol Antes de derribar un árbolTala final Procedimiento de tala Corte de la muescaTronco apoyado en un extremo Desmembramiento DE UN ÁrbolTrozado DE UN Tronco La totalidad del tronco sobre el sueloPoda DE UN Árbol Tronco apoyado sobre ambos extremosPaso ❺ Conecte al cordón de alimentación Ensamble DE LA Sierra DE Pértiga RPS2N1Paso ❷ Inserte el soporte de la pértiga en la sierra Para Cortar CON LA Sierra DE Pértiga Regulación DE LA Longitud DE LA Pértiga RPSN1Mantenimiento normal de la barra de guía Limpieza Y MantenimientoLimpieza DEL Cabezal Cuidado DE LA Barra DE GuíaLimado de los calibradores de medida de profundidad Afilado DE LA CadenaElementos necesarios para afilar la cadena Afilado de los elementos de corteCadenas DE Repuesto AlmacenamientoRecambio DE LA Cadena Serrada Servicio CON Garantía Limpieza Y Mantenimiento Servicio TécnicoAccesorios Y Piezas DE Repuesto Servicio DE ReparaciónFalla Observada Causa Posible Solución Diagnóstico Y Resolución DE ProblemasNuevos Productos Información DE GarantíaManuel Dutilisation ET Dentretien Nettoyage ET Entretien IntroductionConsignes DE Sécurité Importantes Information SUR LA Tronçonneuse SUR TigeLisez Toutes LES Instructions Consignes DE Sécurité ImportantesAvant D’UTILISER LA Tronçonneuse Pendant Lutilisation DE LA Tronçonneuse Recul Entretien ET Remisage DE LA Tronçonneuse Entretien de la tronçonneuse et protection contre le reculDéballage Tronçonneuse Électrique Identification DU ProduitVocabulaire DE LA Tronçonneuse Assemblage DE LA Tronçonneuse Information SUR LA TronçonneuseQuincaillerie Tronçonneuse Comment tourner la vis de réglage Réglage DE LA Tension DE LA ChaîneLubrification DE LA Chaîne Rallonges ÉlectriquesRemplissage DU Réservoir D’HUILE Important N’UTILISEZ PAS d’huile à chaîne standardAvertissement Sciage Avec LA TronçonneuseAbattage D’UN Arbre Avant d’abattre un arbreTrait d’abattage Procédure d’abattage Sifflet d’abattageToute la bille repose au sol ÉbranchageTronçonnage D’UNE Bille Taille D’UN Arbre Élagage La bille est soutenue à une extrémitéLa bille est soutenue aux deux extrémités Étape ❺ Branchement du cordon électrique Quincaillerie Scie À PercheÉtape ❶ Serrer le déclencheur Étape ❷ Insérer le support de la tige dans la poignéeExtenssion de la perche télescopique Comment Couper À L’AIDE LA Scie À PercheEntretien DE LA GUIDE-CHAÎNE Nettoyage ET EntretienNettoyage DU Carter DE Tronçonneuse Avertissement Pournettoyer le carter de la tronçonneuseAffûtage des taillants Affûtage DE LA ChaîneOutils nécessaires pour affûter la chaîne Remisage Remplacement DE LA ChaîneChaînes DE Rechange Service Hors Garantie Service TechniquePièces DE Rechange ET Accessoires Service DE Réparation Service Sous GarantieDéfaillance Cause Possible Remède Observée DépannageDate Purchased Description QTY Parts List / Lista DE Repuestos / Liste DES PiècesParts List / Lista DE Repuestos / Liste DES Pièces DESCRIPTION/DESCRIPCIÓN/DESCRIPTION FBD Parts CENTRAL/CENTRAL DE PIEZAS/DÉPÔT DE PiècesREV.A