Homelite UT80911, UT80709 Packing List, Raising and Lowering the Handle, See Figures 3, English

Page 14

ASSEMBLY

NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and get help when needed.

nInspect the tool carefully to make sure no breakage or damage occurred during shipping.

nDo not discard the packing material until you have care- fully inspected and satisfactorily operated the tool.

nIf any p arts ar e d amaged o r m issing, p lease c all 1-800-242-4672 for assistance.

PACKING LIST

Pressure Washer

25 ft. High Pressure Hose Trigger Handle Holder Trigger Handle

Screw (1/4-20 x 1.65 in., Pan Hd.) Screw (1/4-20 x 1.85 in. Pan Hd.) Screw (1/4-20 x 2.27 in. Pan Hd.) Spray Wand

5-in-1 Change Over Nozzle Injection Hose plus Filter Flat Washer

4-Cycle Engine Lubricant (SAE 30 or SAE 10W30) Hose Storage

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could r esult in serious personal injury.

WARNING:

Do not attempt to modify this product or create acces- sories not recommended for use with this pr oduct. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING:

To prevent accidental starting that could cause serious personal injury, always disconnect the enginespark plug wire from the spark plug when assembling parts.

RAISING AND LOWERING THE HANDLE

See Figure 2.

nTo raise the handle (for moving the pressure washer): pul the handle up until the handle release knob snaps into locking position. Ensure the lock is secured in the frame hole before moving.

nTo lower the handle (for storing or transporting the pres- sure washer): pull the handle release knobout and lower the handle to the down position.

NOTE: The handle can not be locked in the down posi- tion.

Never use the handle tolift the pressure washer. The handle should only be used for moving the unit by r olling it on its wheels.

INSTALLING HOSE STORAGE, TRIGGER HANDLE HOLDER, AND SPRAY WAND HOLDER

See Figures 3 - 4.

nRaise handle as described in the Raising and Lowering Handle section.

nPlace hose storage onto the handle as shown.

nAlign the holes in the hose storage with the holes in the handle.

nInsert bolt (1/4-20 x 1.65 in.) through the holes in the left side of the handle and hose storage.

nPlace nut onto bolt and tighten.

nPlace the trigger handle holder onto the handle as shown.

nAlign the holes in the trigger handleholder with the holes in the hose storage and the handle.

nInsert bolt (1/4-20 x 2.27 in.) through the holes in handle, hose storage, and trigger handle holder.

nTurn bolt while holding the nut in place to tighten and secure.

nPlace spray wand holder onto pressure washer frame.

nAlign the holes in the spray wand holder with the holes in the pressure washer frame.

nInsert screw (1/4-20 x 1.85 in.) through the holes in the spray wand holder and the pressure washer frame.

nPlace nut onto screw and tighten.

ASSEMBLING THE SPRAY WAND TO THE TRIGGER HANDLE

See Figure 5.

nPlace the threaded end of the spray wand in the connector on the end of the trigger handle.

nTurn the connector clockwise until it stops.This secures the spray wand in place.

Page 8 — English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PSI Pressure Washer Save this Manual for Future ReferencePage Page Iii Run marche, marcha E On marche, encendido BAC Page Table of Contents IntroductionRead ALL Instructions Important Safety Instructions Never leave tool running unattended. Turn power off 3 EnglishSpecific Safety Rules 4 EnglishSymbol Name Explanation SymbolsSymbol Signal Meaning 5 English6 English Tools Needed FeaturesAssembly Assembling the Spray Wand to the Trigger Handle Packing ListRaising and Lowering the Handle See Figures 3Connecting the Garden Hose to the Pressure Washer Connecting High Pressure Hose to Trigger HandleConnecting the High Pressure Hose to the Pump Attaching Injection HoseAdding Lubricant to the Engine OperationApplications Oxygenated FuelsStarting and Stopping the Pressure Washer Using the Spray Wand TriggerINSTALLING/REMOVING Nozzles See Figures 13Washing with Detergent Using the 5-IN-1 Change Over NozzleUsing the High Pressure Hose Rinsing with the Pressure WasherMoving the Pressure Washer MaintenanceGeneral Maintenance 13 EnglishChecking Spark Plug Nozzle MaintenanceCleaning the AIR Filter Changing Engine Lubricant15 English Periodic Maintenance SchedulePreparing for USE After Storage 16 English TroubleshootingProblem Cause Solution 17 English WarrantyFederal Emissions Component Defect Warranty General Emissions Warranty Coverage 18 EnglishParts Covered Under the California Emissions Warranty 19 EnglishLimited NON Engine Warranty Statement 20 English21 English Limited Engine WarrantyWarranty Periods Lire Toutes LES Instructions Instructions Importantes Concernant LA SécuritéAVERTISSEMENT  3 FrançaisRègles DE Sécurité Particulières 4 FrançaisSymbole NOM Désignation / Explication SymbolesSymbole Signal Signification Avertissement6 Français Fiche Technique CaractéristiquesAssemblage DéballageAssemblage DE LA Lance EN Position DE Poignée DE Gâchette Liste DE ContrôleRélever ET Abaisser LA Poignée Voir la figures 3Connexion DU Flexible Haute Pression SUR LA Pompe Installation DU Tuyau D’INJECTIONUtilisation Connexion DU Tuyau D’ARROSAGE AU Nettoyeur Haute PressionAppoint D’ESSENCE AJOUT/VÉRIFICATION DE LubrifiantCarburants Oxygénés 10 FrançaisFonctionnement Poignée DE Gâchette INSTALLATION/RETRAIT DES BusesMise EN Marche / Arrêt DU Nettoyeur Haute Pression Voir les figures 13Nettoyage Avec DU Détergent Utilisation DE LA Buse À Permutation 5 ENUtilisation DU Tuyau Haute Pression Rinçage Avec LE Nettoyeur Haute PressionEntretien Général Déplacement DU Nettoyeur Haute PressionEntretien 13 FrançaisVérification D’UNE Bougie Entretien DE BuseNettoyage DU Filtre À AIR Changement Huile DE Moteur15 Français Remise EN Service Après RemisageCalendrier D’ENTRETIEN Périodique 16 Français Problème Cause SolutionDépannage Garantie 17 Français18 Français LA Couverture Generales DE Garantie D’EMISSIONSUniquement en Californie 19 Français ’HAUTE Operation DE Moteur D’ALTITUDEÉnoncé DE LA Garantie Limitée Hors Moteur 20 Français21 Français Garantie Limitée DE MoteurPériodes DE GARANTIE  Instrucciones DE Seguridad Importantes 3 EspañolReglas DE Seguridad Específicas 4 EspañolAdvertencia SímbolosPeligro Precaución6 Español Armado CaracterísticasHerramientas Necesarias Armado DEL Tubo Rociador DE Mango DEL Gatillo Lista DE EmpaquetadoLevantar Y Bajar EL Mango 8 EspañolCómo Conectar LA Manguera DE Inyeccion FuncionamientoConectar DE LA Manguera DE Alta Presión a LA Bomba 9 EspañolCombustibles Oxigenados UsosAbastecimiento DE Lubricante DEL Motor Abastecimiento DEL Tanque DE GasolinaUSO DE LA Boquilla Intercambiable 5 EN USO DEL Mango DEL GatilloInstalar Y Desmontaje LAS Boquillas 11 EspañolEnjuagado CON LA Lavadora DE Presión USO DE LA Manguera DE Alta PresiónLavado CON Detergente Traslado DE LA Lavadora DE PresiónMantenimiento DE LAS Boquillas MantenimientoMantenimiento General Limpieza DEL Filtro DE AireGuardado DE LA Lavadora DE Presión Cambio DE Aceite DE MotorLubricación DE LA Bomba 14 Español15 Español Calendario DE Mantenimiento PeriódicoArtículos de mantenimiento Cada uso Horas 16 Español Solución DE ProblemasProblema Causa Solución Garantía 17 Español18 Español Alcance General DE Garantia DE EmisionesSólo en California 19 Español Operacion Alta DE Motor DE AltitudDeclaración DE Garantía Limitada no Aplicable AL Motor 20 EspañolGarantía Limitada DE Motor 21 EspañolManuel D’UTILISATION OPERATOR’S ManualLavadora a Presión DE 2 700 PSI Manual DEL Operador

UT80709, UT80911 specifications

The Homelite UT80709 and UT80911 are innovative outdoor power equipment models designed to meet the diverse needs of homeowners and professionals alike. These models are part of a larger range that emphasizes performance, durability, and ease of use, making them ideal for a variety of landscaping and gardening tasks.

The Homelite UT80709 is a powerful string trimmer that features a robust 25cc two-cycle engine. This engine ensures strong performance, allowing users to tackle tough overgrowth and trim grass with ease. One of its standout features is the Easy Start technology, which simplifies starting the engine and reduces the amount of pull force required. This is particularly beneficial for users who may struggle with traditional starting mechanisms. The trimmer also boasts an automatic line feed system, ensuring that the cutting line is dispensed as needed without manual intervention, thus enhancing productivity during tasks.

On the other hand, the UT80911 model is a versatile hedge trimmer that comes equipped with a powerful electric motor and a generous blade length. Its dual-action blades provide a smooth, clean cut, significantly reducing vibration and making it comfortable for extended use. The lightweight design of the UT80911 offers easy maneuverability, ensuring that users can reach even the most challenging spots in their gardens or yards. Furthermore, the hedge trimmer incorporates a safety switch feature, which prevents accidental startups, enhancing user safety at all times.

Both models include ergonomic designs with comfortable grips, reducing fatigue during prolonged use. Additionally, the UT80709 and UT80911 are designed with durable materials that withstand the rigors of outdoor use, ensuring longevity and reliability. The Homelite brand is known for its commitment to making outdoor tasks more manageable for users, and these models showcase that philosophy through their user-friendly features and efficient performance.

In conclusion, the Homelite UT80709 and UT80911 represent the brand's dedication to creating powerful, reliable, and user-friendly outdoor equipment. With their advanced technologies and thoughtful design characteristics, these tools are well-suited for both casual gardeners and professional landscapers, making them excellent investments for maintaining beautiful outdoor spaces.
Top Page Image Contents