Homelite UT80709 Connecting High Pressure Hose to Trigger Handle, Attaching Injection Hose

Page 15

ASSEMBLY

CONNECTING HIGH PRESSURE HOSE TO TRIGGER HANDLE

See Figure 6.

nScrew t he co llar o n t he hig h p ressure ho se int o t he trigger handle inlet coupler by turning the hose collar clockwise.

nPull on the hose to be certain it is properly secured.

CONNECTING THE HIGH PRESSURE HOSE TO THE PUMP

See Figure 7.

After the high pressure hose has been uncoiled andattached to the spray wand:

nAlign the collar on the threaded nipple on the pump.

nInsert the nozzle on the end of the high pressure hose collar into the threaded nipple.

nTurn the collar clockwise to tighten the hose securely to the pump.

nPull on the hose to be certain it is properly secured.

CAUTION:

Do not run the pressure washer pump without water sup- ply connected and tur ned on, as this may damage the high pressure seals and decrease pump life. Completely unwind the hose from its reel or coil and make sure the hose is not being restricted by tires, rocks, or any other objects that may lessen or prevent water flow to the pressure washer.

To connect the garden hose to the machine:

nUncoil the garden hose.

NOTE: There must be a min imum of 10 feet of unrestricted hose between the pressure washer intake and the hose faucet or shut off valve (such as a “Y” shut off connector).

nWith the hose faucet turned completely off, attach the end of the garden hose to the water intake. Tighten by hand.

ATTACHING INJECTION HOSE

See Figures 9 - 10.

Before detergent can be used with this machine,the injection hose must be attached.

nPush the open end of the clear injection hose securely over the fitting on the back of the unit.

NOTE: Keep injection hose away from hot surfaces.

nOpen the cap on the detergent tank.

nRemove the filter from the injection hose.

nFrom the top of the cap, slide the injection hose through the hole in the cap.

nPush the injection hose filter onto the end of the injec- tion hose and pull enough hose through the cap so the injection hose filter will rest at the bottom of the detergent tank.

nClose the cap on the detergent tank.

CONNECTING THE GARDEN HOSE TO THE PRESSURE WASHER

See Figure 8.

CAUTION:

Always observe all local regulations when connnecting hoses to the water main. Some areas have restrictions against connecting directly to public drinking water sup- ply to prevent the feedback of chemicals into the drinking water supply. Direct connection through a receiver tank or backflow preventer is usually permitted.

The water supply must come from a water main. NEVER use hot water or water fr om pools, lakes, etc. Befor e connecting the garden hose to the pressure washer:

nRun water through the hose for 30 seconds to cleanany debris from the hose.

nInspect the screen in the water intake.

nIf the screen is damaged, do not use the machine until the screen has been replaced.

nIf the screen is dirty, clean it before connecting the garden hose to the machine.

Page 9 — English

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Save this Manual for Future Reference PSI Pressure WasherPage Page Iii Run marche, marcha E On marche, encendido BAC Page Introduction Table of Contents3 English Important Safety Instructions Never leave tool running unattended. Turn power off Read ALL Instructions4 English Specific Safety Rules5 English SymbolsSymbol Signal Meaning Symbol Name Explanation6 English Features AssemblyTools Needed See Figures 3 Packing ListRaising and Lowering the Handle Assembling the Spray Wand to the Trigger HandleAttaching Injection Hose Connecting High Pressure Hose to Trigger HandleConnecting the High Pressure Hose to the Pump Connecting the Garden Hose to the Pressure WasherOxygenated Fuels OperationApplications Adding Lubricant to the EngineSee Figures 13 Using the Spray Wand TriggerINSTALLING/REMOVING Nozzles Starting and Stopping the Pressure WasherRinsing with the Pressure Washer Using the 5-IN-1 Change Over NozzleUsing the High Pressure Hose Washing with Detergent13 English MaintenanceGeneral Maintenance Moving the Pressure WasherChanging Engine Lubricant Nozzle MaintenanceCleaning the AIR Filter Checking Spark PlugPeriodic Maintenance Schedule Preparing for USE After Storage15 English Troubleshooting Problem Cause Solution16 English Warranty Federal Emissions Component Defect Warranty17 English 18 English General Emissions Warranty Coverage19 English Parts Covered Under the California Emissions Warranty20 English Limited NON Engine Warranty StatementLimited Engine Warranty Warranty Periods21 English 3 Français Instructions Importantes Concernant LA SécuritéAVERTISSEMENT  Lire Toutes LES Instructions4 Français Règles DE Sécurité ParticulièresAvertissement SymbolesSymbole Signal Signification Symbole NOM Désignation / Explication6 Français Déballage CaractéristiquesAssemblage Fiche TechniqueVoir la figures 3 Liste DE ContrôleRélever ET Abaisser LA Poignée Assemblage DE LA Lance EN Position DE Poignée DE GâchetteConnexion DU Tuyau D’ARROSAGE AU Nettoyeur Haute Pression Installation DU Tuyau D’INJECTIONUtilisation Connexion DU Flexible Haute Pression SUR LA Pompe10 Français AJOUT/VÉRIFICATION DE LubrifiantCarburants Oxygénés Appoint D’ESSENCEVoir les figures 13 INSTALLATION/RETRAIT DES BusesMise EN Marche / Arrêt DU Nettoyeur Haute Pression Fonctionnement Poignée DE GâchetteRinçage Avec LE Nettoyeur Haute Pression Utilisation DE LA Buse À Permutation 5 ENUtilisation DU Tuyau Haute Pression Nettoyage Avec DU Détergent13 Français Déplacement DU Nettoyeur Haute PressionEntretien Entretien GénéralChangement Huile DE Moteur Entretien DE BuseNettoyage DU Filtre À AIR Vérification D’UNE BougieRemise EN Service Après Remisage Calendrier D’ENTRETIEN Périodique15 Français Problème Cause Solution Dépannage16 Français 17 Français GarantieLA Couverture Generales DE Garantie D’EMISSIONS Uniquement en Californie18 Français ’HAUTE Operation DE Moteur D’ALTITUDE 19 Français20 Français Énoncé DE LA Garantie Limitée Hors MoteurGarantie Limitée DE Moteur Périodes DE GARANTIE 21 Français 3 Español Instrucciones DE Seguridad Importantes4 Español Reglas DE Seguridad EspecíficasPrecaución SímbolosPeligro Advertencia6 Español Características Herramientas NecesariasArmado 8 Español Lista DE EmpaquetadoLevantar Y Bajar EL Mango Armado DEL Tubo Rociador DE Mango DEL Gatillo9 Español FuncionamientoConectar DE LA Manguera DE Alta Presión a LA Bomba Cómo Conectar LA Manguera DE InyeccionAbastecimiento DEL Tanque DE Gasolina UsosAbastecimiento DE Lubricante DEL Motor Combustibles Oxigenados11 Español USO DEL Mango DEL GatilloInstalar Y Desmontaje LAS Boquillas USO DE LA Boquilla Intercambiable 5 ENTraslado DE LA Lavadora DE Presión USO DE LA Manguera DE Alta PresiónLavado CON Detergente Enjuagado CON LA Lavadora DE PresiónLimpieza DEL Filtro DE Aire MantenimientoMantenimiento General Mantenimiento DE LAS Boquillas14 Español Cambio DE Aceite DE MotorLubricación DE LA Bomba Guardado DE LA Lavadora DE PresiónCalendario DE Mantenimiento Periódico Artículos de mantenimiento Cada uso Horas15 Español Solución DE Problemas Problema Causa Solución16 Español 17 Español GarantíaAlcance General DE Garantia DE Emisiones Sólo en California18 Español Operacion Alta DE Motor DE Altitud 19 Español20 Español Declaración DE Garantía Limitada no Aplicable AL Motor21 Español Garantía Limitada DE MotorManual DEL Operador OPERATOR’S ManualLavadora a Presión DE 2 700 PSI Manuel D’UTILISATION

UT80709, UT80911 specifications

The Homelite UT80709 and UT80911 are innovative outdoor power equipment models designed to meet the diverse needs of homeowners and professionals alike. These models are part of a larger range that emphasizes performance, durability, and ease of use, making them ideal for a variety of landscaping and gardening tasks.

The Homelite UT80709 is a powerful string trimmer that features a robust 25cc two-cycle engine. This engine ensures strong performance, allowing users to tackle tough overgrowth and trim grass with ease. One of its standout features is the Easy Start technology, which simplifies starting the engine and reduces the amount of pull force required. This is particularly beneficial for users who may struggle with traditional starting mechanisms. The trimmer also boasts an automatic line feed system, ensuring that the cutting line is dispensed as needed without manual intervention, thus enhancing productivity during tasks.

On the other hand, the UT80911 model is a versatile hedge trimmer that comes equipped with a powerful electric motor and a generous blade length. Its dual-action blades provide a smooth, clean cut, significantly reducing vibration and making it comfortable for extended use. The lightweight design of the UT80911 offers easy maneuverability, ensuring that users can reach even the most challenging spots in their gardens or yards. Furthermore, the hedge trimmer incorporates a safety switch feature, which prevents accidental startups, enhancing user safety at all times.

Both models include ergonomic designs with comfortable grips, reducing fatigue during prolonged use. Additionally, the UT80709 and UT80911 are designed with durable materials that withstand the rigors of outdoor use, ensuring longevity and reliability. The Homelite brand is known for its commitment to making outdoor tasks more manageable for users, and these models showcase that philosophy through their user-friendly features and efficient performance.

In conclusion, the Homelite UT80709 and UT80911 represent the brand's dedication to creating powerful, reliable, and user-friendly outdoor equipment. With their advanced technologies and thoughtful design characteristics, these tools are well-suited for both casual gardeners and professional landscapers, making them excellent investments for maintaining beautiful outdoor spaces.
Top Page Image Contents