Homelite UT80911, UT80709 Using the 5-IN-1 Change Over Nozzle, Using the High Pressure Hose

OPERATION

USING THE 5-IN-1 CHANGE OVER NOZZLE

See Figure 17.

There are five spray pattern settings located on the 5-in-1 Change Over Nozzle. To select a spray pattern, rotate the spray selector to the desired setting.

Nozzle	Application
	Spot cleaning of high, hard-to-reach areas
	• Removing caked-on mud from heavy con-
0º	struction, farm, or lawn equipment
	• Cleaning tar, glue, or stubborn stains from
	concrete
	• Cleaning overhead areas
	• Removing rust from steel and oxidation
	from aluminum
	For general purpose or large surfaces
	• General cleaning of dirt, mud, and grime
25º	• Cleaning roofs, gutters, and downspouts
	• Removing light mildew stains
	• Removing algae and bacteria build-up from
	pools
	• Rinsing surfaces in preparation for painting­
	For wide-angle rinsing
	• Light cleaning and washing
40º	• Washing and rinsing of painted surfaces
	and boats
	• Cleaning roofs, windows, patios, and
	driveways
	For short range detergent applications
	• Driveways, walkways, decks and patios,
Soap	vehicles, fences, paint prep, patio furniture,
Short	and lawn equipment
Range
	For long range detergent applications
	• Second story washing
Soap
Long
Range

USING THE HIGH PRESSURE HOSE

The high pressure hose features an outer covering that pro- vides strength to the hose. If the outer covering becomes damaged, the hose must be replaced immediately. Do not use a high pressure hose if the outer covering is damaged.

To prevent damage to the outer covering:

nInspect the hose before every use.

nFully unwrap and straighten hose before use.

nDo not allow the high pressure hose to be kinked.

nKeep hose away from hot surfaces and sharp edges.

nDo not pull unit by high pressure hose.

nDo no t allo w ho se t o b e crus hed o r w rapped ar ound objects.

WASHING WITH DETERGENT

See Figures 18 - 19.

Use only detergents designed forpressure washers; house- hold detergents, acids, alkalines, bleaches, solvents, flam- mable material, or industrial grade solutions can damage the pump. Many detergents may require mixing priorto use. Prepare cleaning solution as instructed on the solution bottle.

nRemove the cap from the detergent container and pour detergent in the container. Replace cap on container.

nRotate the spray selector on the 5-in-1 Change Over

Nozzle to either the SoapShort Range [] or Soap Long Range [] setting.

nSpray the detergent on a dry surface using long, even, overlapping strokes. To prevent streaking, do not allow detergent to dry on the surface.

NOTE: To use a detergent bottle, open the detergent container cap. Next, remove the filter from the end of the injectionhose then slide the hose out of the cap. Place the injection hose filter back on the hose and place the hose in the bottom of the bottle.

For long range detergent application:

With the nozzle installed on the spray wand and the engine shut off, rotate the spray selector to the Soap Long Range [] setting.

For short range detergent application:

With the nozzle installed on the spray wand and the engine shut off, rotate the spray selector to the Soap Short Range [] setting.

Before shutting off the engine:

nPlace the injection hose in a bucket of clean water.

nFlush for 1 - 2 minutes (spray clear water through the spray wand).

nShut off the engine.

NOTE: Shutting OFF ( O ) the engineWILL NOT relieve pres- sure in the system. Pull trigger to release water pressure.

RINSING WITH THE PRESSURE WASHER

n Turn off the pressure washer and shut off the water supply. Pull trigger to release water pressure.

nEngage the lock out on the trigger handle by pushing up on the lock out until it clicks into the slot.

nRotate the spray selector on the 5-in-1 Change Over Nozzle to either the [40º], [25º], or [0º] setting depending on the job. Refer to the chart inUsing the 5-in-1 Change Over Nozzle to determine which setting is correct for your application.

Page 12 — English