DeWalt DP3900 Maintenance, Shutting Down, refer to Chemicals and Cleaning, Solvents, English

Page 13
refer to Chemicals and Cleaning

Solvents.WARNING: To reduce the possibility of contamination always pro- tect against backflow when connected to a potable water system.

6.

Connect high-pressure hose (C) to pump

C

 

outlet.

7.

If applying a chemical or cleaning solution,

 

 

refer to Chemicals and Cleaning

 

 

Solvents.

 

8.

Turn the water source on.

 

CAUTION: Risk of property damage. Failure

X

to do so could cause damage to the pump.

 

9.Remove all air from the pump and high pressure hose by depress- ing trigger until a steady stream of water is present.

10.Start engine. Refer to the engine instruction manual for correct procedure.

Shutting DownWARNING: Risk of unsafe operation. If engine does not start after two pulls, squeeze trigger of gun to relieve pump pressure. Pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury.

11. Depress trigger on gun to start water flow.

MAINTENANCEWARNING: Risk of unsafe operation. Stand on a stable surface and grip gun/wand firmly with both hands. Expect the gun to kickback when triggered.

12. Release trigger to stop water flow.

DANGER: Risk of injury from spray. Engage the

Y

trigger lock (Y) when gun is not in use to prevent

 

accidental spraying.

13. Adjust spray for the task being performed by changing quick connect nozzle. Refer to Spray Wand Nozzles.

Shutting Down

1.If chemicals were applied, place the chemical hose into a container of clean water and draw clean water through chemical injection system to rinse system thoroughly.

CAUTION: Risk of property damage Failure to do so could cause damage to the pump.

2.Turn engine off. Refer to the engine instruction manual. CAUTION: Risk of property damage. NEVER turn water supply off while pressure washer engine is running or damage to pump will result.

3.Turn water source off.

4.Pull trigger on spray gun to relieve any water pressure in hose or spray gun.

5.Refer to Storage for proper storage procedures.

MAINTENANCE

Manual backgroundWARNING: Risk of burning. When performing maintenance, you may be exposed to hot surfaces, water pressure or moving parts that can cause serious injury or death.

Manual backgroundWARNING: Risk of fire. Always disconnect, spark plug wire, let the engine cool and release all water pressure before performing any maintenance or repair. The engine contains flammable fuel. Do not smoke or work near open flames while performing maintenance.

To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high temperatures or dusty conditions, more frequent maintenance checks will be required.

English

13

Image 13
Contents If you have questions or comments, contact us GUIDE DUTILISATION MANUAL DE INSTRUCCIONESPour toute question ou tout commentaire, nous contacter Si tiene dudas o comentarios, contáctenosEnglish WEIGHTEngine Pump SpecificationsImportant Safety Instructions Definitions Safety GuidelinesSAVE THESE INSTRUCTIONS 1-800-4-DEWALTEnglish HOW TO PREVENT ITDANGER RISK OF EXPLOSION OR FIRE WHAT CAN HAPPENDANGER RISK OF FLUID INJECTION AND LACERATION DANGER RISK TO BREATHING ASPHYXIATION CONTINUEDDANGER RISK OF UNSAFE OPERATION DANGER RISK OF INJURY FROM SPRAYDANGER RISK OF INJURY OR PROPERTY DAMAGE WHEN TRANSPORTING OR STORING WARNING RISK OF HOT SURFACES WARNING RISK OF BURSTINGWARNING RISK OF CHEMICAL BURN SAVE THESE INSTRUCTIONS FOR FUTURE USE INSTALLATION Pressure Washer Assembly FigWARNING RISK OF ELECTRICAL SHOCK WARNING RISK OF INJURY FROM LIFTINGSpray Wand Nozzles Fig OPERATION Pressure AdjustmentsCHANGING NOZZLES ON SPRAY WAND Chemicals and Cleaning Solventsuse. Do not use bleach TO APPLY CHEMICALS AND SOLVENTSStarting START-UP PROCEDURErefer to Chemicals and Cleaning MAINTENANCEShutting Down SolventsNozzle Cleaning To Clean the Water Inlet FilterHOW TO CHANGE PumpTo Remove Tires ACCESSORIESSTORAGE Engine Pressure WasherLimited Warranty SERVICE INFORMATIONRepairs Date and Place of PurchaseProblem Troubleshooting GuideGlossary CodePOSSIBLE SOLUTION Troubleshooting CodesCODE POSSIBLE CAUSETroubleshooting Codes cont Moteur FrançaisCaractéristiques techniques de la pompe LAVEUSE HAUTE PRESSION, MODÈLE DP3900Définitions lignes directrices en matière de sécurité Fiche techniqueDirectives de sécurité importantes et des conditions de fonctionnement et d’autres variablesDANGER RISQUE D’EXPLOSION OU D’INCENDIE CONSERVER CES DIRECTIVESCE QUI PEUT SE PRODUIRE COMMENT L’ÉVITERDANGER RISQUE D’ASPHYXIE SUITE DANGER RISQUE D’INJECTION ET DE LACÉRATIONDANGER RISQUE D’UTILISATION DANGEREUSE DANGER RISQUE DE BLESSURE PAR JETSuivre la procédure de AVERTISSEMENT RISQUE D’ÉCLATEMENT FrançaisAVERTISSEMENT ATTENTION SURFACES CHAUDES AVERTISSEMENT RISQUE DE BRÛLURE CHIMIQUECONSERVER CES DIRECTIVES POUR UN USAGE ULTÉRIEUR INSTALLATION Assemblage de la laveuse haute pression FigAVERTISSEMENT RISQUE DECHOC ÉLECTRIQUE AVERTISSEMENT RISQUE DE BLESSURE EN SOULEVANT LE PRODUITFONCTIONNEMENT Réglages de la pression CHANGEMENT DES BUSES SUR LE TUBE DE PULVÉRISATION Buses du tube de pulvérisation FigDémarrage Produits chimiques et solvants de nettoyageAPPLICATION DE PRODUITS CHIMIQUES ET SOLVANTS section Produits chimiques et solvants PROCÉDURE DE DÉMARRAGEde nettoyage Mise à l’arrêt de l’appareil ENTRETIENNettoyage du filtre de l’admission d’eau PompeNettoyage des buses VÉRIFICATION DU NIVEAU D’HUILERANGEMENT Moteur Retrait des pneuLaveuse haute pression INFORMATION SUR LES RÉPARATIONS ACCESSOIRESRéparations Garantie limitéeTube de pulvérisation à branchement rapide ce système permet GlossaireGuide de dépannage SOLUTION PROBABLECodes de dépannage ProblèmeConsulter la section Buses du tube de pulvérisation sous Codes de dépannage suiteS’assurer que l’extrémité du tuyau pour produit chimique soit entière Especificaciones de la bomba MotorEspañol LAVADORA A PRESIÓN CON MOTOR A DP3900Definiciones Normas de seguridad EspecificacionesInstrucciones de seguridad importantes MODELOPELIGRO RIESGO DE EXPLOSIÓN O INCENDIO CONSERVE ESTAS INSTRUCCIONES¿QUÉ PUEDE SUCEDER? CÓMO EVITARLOPELIGRO RIESGO RESPIRATORIO ASFIXIA PELIGRO RIESGO DE INYECCIÓN DE LÍQUIDO Y LACERACIÓN PELIGRO RIESGO DE INYECCIÓN DE LÍQUIDO Y LACERACIÓN CONTINUARPELIGRO RIESGO DE LESIÓN POR PULVERIZACIÓN PELIGRO RIESGO DE OPERACIÓN INSEGURAAL TRANSPORTAR O ALMACENAR LA UNIDAD PELIGRO RIESGO DE LESIÓN O DAÑO A LA PROPIEDADADVERTENCIA RIESGO DE SUPERFICIES CALIENTES ADVERTENCIA RIESGO DE DE ESTALLIDOADVERTENCIA RIESGO DE QUEMADURA QUÍMICA CONSERVE ESTAS INSTRUCCIONES PARA FUTURAS CONSULTAS INSTALACIÓN Ensamblado de la lavadora a presión FigADVERTENCIA RIESGO DE DESCARGA ELÉCTRICA ADVERTENCIA RIESGO DE LESIÓN POR LEVANTAR MUCHO PESOOPERACIÓN Ajustes a la presión Color de la Boquillas para la varilla pulverizadora FigPatrón de UsosPuesta en marcha Productos químicos y solventes de limpiezaPARA APLICAR PRODUCTOS QUÍMICOS Y SOLVENTES PROCEDIMIENTO DE PUESTA EN MARCHA MANTENIMIENTO Apagado2. Apague el motor. Consulte el manual de instrucciones del motor Limpieza de las boquillas BombaPara limpiar el filtro de entrada de agua PARA CONTROLAR EL ACEITEALMACENAMIENTO Motor Para quitar los neumáticosLavadora a presión INFORMACIÓN DE MANTENIMIENTO ACCESORIOSReparaciones Póliza de GarantíaEXCEPCIONES Garantía limitadaProductos químicos y solventes de limpieza GlosarioCódigos de detección de problemas Guía de detección de problemasProblema CódigoConsulte la sección Boquillas para la varilla pulverizadora en Códigos de detección de problemas continuar CÓDIGO CAUSA POSIBLE 701 Joppa Road, Baltimore, MD D EWALT Industrial Tool CoNOV06 Form No. A20832