DeWalt A16505, DP2800 Start-up Procedure, Connect high-pressure hose C to pump Outlet

Page 12

English

•Never turn water supply off while pressure washer engine is running or damage to pump will result.

• DO NOT stop spraying water for more than two

 

minutes at a time. Pump operates in bypass

 

mode when spray gun trigger is not pressed.

 

When the temperature inside the pump rises

 

too high the thermal relief valve (T) will open

 

and release a gush of water in an effort to lower

T

the temperature inside the pump. The thermal

 

relief valve will then close. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged.

Start-up Procedure

1.In a well-ventilated outdoor area, add fresh, high-quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine instruction manual for correct procedure.

2.Check engine oil level. Refer to the engine instruction manual for correct procedure.

3.Connect the water hose to the water source. Turn the water source on to remove all air from the hose. When a steady stream of water is present, turn the water source off.

4.Verify the filter screen (U) is in water inlet of

pump. The cone side faces out.

5. Connect the cold water source (V) to pump inlet.

NOTE: Water source must provide a minimum

 

of 5 gallons per minute at 20 pSI.

U

Warning: To reduce the possibility of con-

 

tamination always protect against backflow when connected to a potable water system.

6.

Connect high-pressure hose (C) to pump

c

 

outlet.

7.

If applying a chemical or cleaning solution,

 

 

refer to Chemicals and Cleaning

 

 

Solvents.

 

8.

Turn the water source on.

 

Caution: Risk of property damage. Failure

V

to do so could cause damage to the pump.

 

9.Remove all air from the pump and high pressure hose by depress- ing trigger until a steady stream of water is present.

10.Start engine. Refer to the engine instruction manual for correct procedure.

Warning: Risk of unsafe operation. If engine does not start after two pulls, squeeze trigger of gun to relieve pump pressure. Pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury.

11. Depress trigger on gun to start water flow.

Warning: Risk of unsafe operation. Stand on a stable surface and grip gun/wand firmly with both hands. Expect the gun to kickback when triggered.

12. Release trigger to stop water flow.

DANGER: Risk of injury from spray. Engage the

W

trigger lock (W) when gun is not in use to prevent

 

accidental spraying.

 

13. Adjust spray for the task being performed by changing quick connect nozzle. Refer to Spray Wand Nozzles.

Shutting Down

1.If chemicals were applied, place the chemical hose into a container of clean water and draw clean water through chemical injection system to rinse system thoroughly.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents DP2800 Pressure Washer Laveuse à pression Lavadora a presión Pump Specifications SpecificationsModel Weight Height Width CAT 3DX29GSIDefinitions Safety Guidelines Important Safety InstructionsDeWALT What can happen How to prevent it Risk to Breathing Asphyxiation What can happenEnglish Never leave wand unattended while unit is runningIf engine does not start after Two pulls, squeeze triggerGun to relieve pump Pressure. Pull starter cordTo these very rapidly. Adjust Use a tire pressure gaugeTo check the tires pressure Before each use and whileFor Future USE Installation Pressure Washer Assembly FigPressure Adjustments OperationSpray Wand Nozzles Fig Changing Nozzles on Spray WandChemicals and Cleaning Solvents StartingTo apply chemicals and solvents Start-up Procedure Refer to Chemicals and Cleaning SolventsConnect high-pressure hose C to pump Outlet Turn the water source onMaintenance How To Change Pump OilEngine Pump To Check OilTo Clean the Water Inlet Filter To Remove TiresSTORAGE Engine Pump Accessories Service Information Limited WarrantyPressure Washer RepairsEnglish Glossary Troubleshooting Guide Problem CodeTroubleshooting Codes Possible SolutionCode Possible cause Troubleshooting Codes Caractéristiques techniques de la pompe Fiche techniqueMoteur Définitions lignes directrices en Matière de sécurité Directives de sécurité importantesConserver CES Directives CE QUI Peut SE Produire Comment L’ÉVITER CE QUI Peut SE Produire Comment l’éviter Risque D’INJECTION et de lacération suite Suivre la procédure de Démarrage correcte pourQui provoquerait ainsi une Au brasAvertissement Risque d’éclatement Français Assemblage de la laveuse haute pression Fig Jusqu’à ce que les boutons soient solidement fixesFonctionnement Réglages de la pressionBuses du tube de pulvérisation Fig Changement DES Buses SUR LE Tube DE PulvérisationProduits chimiques et solvants de nettoyage DémarrageApplication DE Produits Chimiques ET Solvants Procédure DE Démarrage Raccorder le tuyau haute pression C à la Sortiede la pompeChimique ou de nettoyant, se reporter à la Section Produits chimiques et solvants De nettoyageEntretien MoteurPompe Nettoyage du filtre de l’admission d’eauVérification DU Niveau D’HUILE Méthode DE Vidange DE L’HUILE DE LA PompeRetrait des pneu RangementLaveuse haute pression Glisser le collet hors de l’essieu et retirer le pneuAccessoires Information SUR LES RéparationsRéparations Garantie limitéeFrançais Glossaire Solution Probable Guide de dépannageCodes de dépannage Problème CodeCodes de dépannage suite Français Especificaciones de la bomba EspecificacionesMotor CAT 3DX29GsIDefiniciones Normas de seguridad Instrucciones de seguridad importantesConserve Estas Instrucciones GravesPeligro Riesgo de explosión o incendio ¿Qué puede suceder? Cómo evitarloPeligro Riesgo Respiratorio asfixia Peligro Riesgo DE Inyección DE Líquido y laceraciónAsegúrese de que la La carne humana y animalPor ello podría ocasionar Simple Corte ConsultePeligro Riesgo de operación insegura Propiedad Observe el flanco para ver laNota Los tanques de aire Los compresores y el equipoConserve Estas Instrucciones Para Futuras Consultas Advertencia Riesgo de quemadura químicaInstalación Ensamblado de la lavadora a presión FigOperación Ajustes a la presiónBoquillas para la varilla pulverizadora Fig Cambio DE LAS Boquillas DE LA Varilla PulverizadoraProductos químicos y solventes de limpieza Puesta en marchaPara Aplicar Productos Químicos Y Solventes Procedimiento DE Puesta EN Marcha Limpieza, consulte la sección ProductosQuímicos y solventes de limpieza Abra la fuente de aguaApagado MantenimientoMotor Suelte el disparador para detener el flujo de aguaBomba Limpieza de las boquillasPara limpiar el filtro de entrada de agua Para Controlar EL AceitePara quitar los neumáticos AlmacenamientoLavadora a presión BombaAccesorios Información DE MantenimientoReparaciones Póliza de GarantíaGarantía limitada Glosario Para Otras Localidades Llame AL 55 5326Guía de detección de problemas Códigos de detección de problemasProblema Código Código Causa posibleOperación Códigos de detección de problemas continuar Español DeWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD JAN06 Form No. A16505 DP2800 Copyright 2006 DeWALT
Top Page Image Contents