DeWalt DP2800, A16505 instruction manual Risk to Breathing Asphyxiation, What can happen

Page 5

RISK TO BREATHING (Asphyxiation) continued

• Some cleaning fluids	• Use only cleaning fluids
contain substances which		specifcally recommended
could cause injury to skin,		for high-pressure washers.
eyes or lungs.		Follow manufacturers
		recommendations. Do not
		use chlorine bleach or any
		other corrosive compound.

DANGER: RISK of FLUID INJECTION and Laceration

•	Direct spray away from self
	and others.
•	Make sure hose and fittings
	are tightened and in good
	condition. Never hold onto
	the hose or fittings during
	opertion.
•	Do not allow hose to contact
	muffler.
•	Never attach or remove wand
	or hose fittings while system
	is pressurized.

English

What can happen

•Your pressure washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries.

DO NOT TREAT FLUID INJECTION AS

A SIMPLE CUT! See a physician immediately!

How to prevent it

•Inspect the high-pressure hose regularly. Replace the hose immediately if it is damaged, worn, has melted from contacting the engine, or shows any signs of cracks, bubbles, pinholes, or other leakage. Never grasp a high-pressure hose that

is leaking or damaged.

•Never touch, grasp or attempt to cover a pinhole or similar water leak on the high- pressure hose. The stream of water IS under high pressure and WILL penetrate skin.

•Never place hands in front of nozzle.

•Injuries can result if system pressure is not reduced before attempting maintenance or disassembly.

•	To relieve system pressure,
	shut off engine, turn off water
	supply and pull gun trigger
	until water stops flowing.
•	Use only accessories rated
	equal to or higher than the
	rating of the pressure washer.

Image 5

Contents DP2800 Pressure Washer Laveuse à pression Lavadora a presión Specifications Pump SpecificationsModel Weight Height Width CAT 3DX29GSIDeWALT Definitions Safety GuidelinesImportant Safety Instructions What can happen How to prevent it What can happen Risk to Breathing AsphyxiationNever leave wand unattended while unit is running EnglishTwo pulls, squeeze trigger If engine does not start afterGun to relieve pump Pressure. Pull starter cordUse a tire pressure gauge To these very rapidly. AdjustTo check the tires pressure Before each use and whilePressure Washer Assembly Fig For Future USE InstallationOperation Pressure AdjustmentsSpray Wand Nozzles Fig Changing Nozzles on Spray WandTo apply chemicals and solvents Chemicals and Cleaning SolventsStarting Refer to Chemicals and Cleaning Solvents Start-up ProcedureConnect high-pressure hose C to pump Outlet Turn the water source onHow To Change Pump Oil MaintenanceEngine Pump To Check OilSTORAGE Engine Pump To Clean the Water Inlet FilterTo Remove Tires Limited Warranty Accessories Service InformationPressure Washer RepairsEnglish Glossary Problem Code Troubleshooting GuideCode Possible cause Troubleshooting CodesPossible Solution Troubleshooting Codes Moteur Caractéristiques techniques de la pompeFiche technique Conserver CES Directives Définitions lignes directrices en Matière de sécuritéDirectives de sécurité importantes CE QUI Peut SE Produire Comment L’ÉVITER CE QUI Peut SE Produire Comment l’éviter Risque D’INJECTION et de lacération suite Démarrage correcte pour Suivre la procédure deQui provoquerait ainsi une Au brasAvertissement Risque d’éclatement Français Jusqu’à ce que les boutons soient solidement fixes Assemblage de la laveuse haute pression FigRéglages de la pression FonctionnementBuses du tube de pulvérisation Fig Changement DES Buses SUR LE Tube DE PulvérisationApplication DE Produits Chimiques ET Solvants Produits chimiques et solvants de nettoyageDémarrage Raccorder le tuyau haute pression C à la Sortiede la pompe Procédure DE DémarrageChimique ou de nettoyant, se reporter à la Section Produits chimiques et solvants De nettoyageMoteur EntretienNettoyage du filtre de l’admission d’eau PompeVérification DU Niveau D’HUILE Méthode DE Vidange DE L’HUILE DE LA PompeRangement Retrait des pneuLaveuse haute pression Glisser le collet hors de l’essieu et retirer le pneuInformation SUR LES Réparations AccessoiresRéparations Garantie limitéeFrançais Glossaire Guide de dépannage Solution ProbableCodes de dépannage Problème CodeCodes de dépannage suite Français Especificaciones Especificaciones de la bombaMotor CAT 3DX29GsIInstrucciones de seguridad importantes Definiciones Normas de seguridadConserve Estas Instrucciones Graves¿Qué puede suceder? Cómo evitarlo Peligro Riesgo de explosión o incendioPeligro Riesgo DE Inyección DE Líquido y laceración Peligro Riesgo Respiratorio asfixiaLa carne humana y animal Asegúrese de que laPor ello podría ocasionar Simple Corte ConsultePeligro Riesgo de operación insegura Observe el flanco para ver la PropiedadNota Los tanques de aire Los compresores y el equipoAdvertencia Riesgo de quemadura química Conserve Estas Instrucciones Para Futuras ConsultasEnsamblado de la lavadora a presión Fig InstalaciónOperación Ajustes a la presiónCambio DE LAS Boquillas DE LA Varilla Pulverizadora Boquillas para la varilla pulverizadora FigPara Aplicar Productos Químicos Y Solventes Productos químicos y solventes de limpiezaPuesta en marcha Limpieza, consulte la sección Productos Procedimiento DE Puesta EN MarchaQuímicos y solventes de limpieza Abra la fuente de aguaMantenimiento ApagadoMotor Suelte el disparador para detener el flujo de aguaLimpieza de las boquillas BombaPara limpiar el filtro de entrada de agua Para Controlar EL AceiteAlmacenamiento Para quitar los neumáticosLavadora a presión BombaInformación DE Mantenimiento AccesoriosReparaciones Póliza de GarantíaGarantía limitada Para Otras Localidades Llame AL 55 5326 GlosarioCódigos de detección de problemas Guía de detección de problemasProblema Código Código Causa posibleOperación Códigos de detección de problemas continuar Español JAN06 Form No. A16505 DP2800 Copyright 2006 DeWALT DeWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD