DeWalt A16505, DP2800 To Clean the Water Inlet Filter, To Remove Tires, STORAGE Engine Pump

Page 14

English

3.

Disconnect the spray wand from the gun.

 

Z

4.

Remove the high-pressure nozzle from

 

 

the spray wand. Remove any obstructions

 

 

with the nozzle cleaning tool (Z) provided

 

 

and back flush with clean water.

 

 

 

5. Direct water supply into spray wand to back flush loosened particles for 30 seconds.

6.Reassemble the nozzle to the wand.

7.Reconnect spray wand to gun then turn on water supply.

8.Start pressure washer and place spray wand into high pressure setting to test.

To Clean the Water Inlet Filter

This filter screen (U) should be checked periodically and cleaned if necessary.

1. Remove the filter screen (U) by grasping the end and removing it from water inlet of pump.

2. Clean filter by flushing it with water on both

U

sides.

3.Reinsert filter into water inlet of pump. Cone side faces out.

NOTE: Do not operate pressure washer without filter properly installed.

To Remove Tires

1. Using a 1/8" hex head wrench loosen set screw in hub collar.

2. Slide hub collar from axle and remove the tire.

sTORAGE Engine

Consult the engine instruction manual for the man­facturer's recommendations for storage.

Pump

The manufacturer recommends using a pump protector/winterizer, such as DP80 when storing the unit for more than 30 days and/or when freezing temperatures are expected. DP80 is availabe at the store where the pressure washer was purchased. If a pump protector/ winterizer is not available, RV antifreeze or windshield washer fluid needs to be run through the pump as outlined in the steps below.

NOTE: Using a pump protector/ winterizer, RV antifreeze or wind- shield washer fluid is to provide proper lubrication to the internal seals of the pump regardless of temperature or environment.

1.Obtain a funnel, 6 oz. (172 ml) of RV antifreeze or windshield washer fluid, and 16–36" (91 cm) of garden hose with a male hose connector attached to one end.

CAUTION: Risk of property damage. Use only RV antifreeze. Any other antifreeze is corrosive and can damage pump.

2.Disconnect spark plug wire.

3.Connect length of garden hose to water inlet of pump.

4. Add RV antifreeze or windshield washer fluid to hose as shown.

5. Pull engine starter rope slowly several times until antifreeze/ washer fluid comes out of high- pressure hose connection of pump.

6. Remove garden hose from water inlet of pump.

7. Reconnect spark plug wire.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents DP2800 Pressure Washer Laveuse à pression Lavadora a presión Model Weight Height Width Pump SpecificationsSpecifications CAT 3DX29GSIDeWALT Definitions Safety GuidelinesImportant Safety Instructions What can happen How to prevent it Risk to Breathing Asphyxiation What can happenEnglish Never leave wand unattended while unit is runningGun to relieve pump If engine does not start afterTwo pulls, squeeze trigger Pressure. Pull starter cordTo check the tires pressure To these very rapidly. AdjustUse a tire pressure gauge Before each use and whileFor Future USE Installation Pressure Washer Assembly FigSpray Wand Nozzles Fig Pressure AdjustmentsOperation Changing Nozzles on Spray WandTo apply chemicals and solvents Chemicals and Cleaning SolventsStarting Connect high-pressure hose C to pump Outlet Start-up ProcedureRefer to Chemicals and Cleaning Solvents Turn the water source onEngine Pump MaintenanceHow To Change Pump Oil To Check OilSTORAGE Engine Pump To Clean the Water Inlet FilterTo Remove Tires Pressure Washer Accessories Service InformationLimited Warranty RepairsEnglish Glossary Troubleshooting Guide Problem CodeCode Possible cause Troubleshooting CodesPossible Solution Troubleshooting Codes Moteur Caractéristiques techniques de la pompeFiche technique Conserver CES Directives Définitions lignes directrices en Matière de sécuritéDirectives de sécurité importantes CE QUI Peut SE Produire Comment L’ÉVITER CE QUI Peut SE Produire Comment l’éviter Risque D’INJECTION et de lacération suite Qui provoquerait ainsi une Suivre la procédure deDémarrage correcte pour Au brasAvertissement Risque d’éclatement Français Assemblage de la laveuse haute pression Fig Jusqu’à ce que les boutons soient solidement fixesBuses du tube de pulvérisation Fig FonctionnementRéglages de la pression Changement DES Buses SUR LE Tube DE PulvérisationApplication DE Produits Chimiques ET Solvants Produits chimiques et solvants de nettoyageDémarrage Chimique ou de nettoyant, se reporter à la Procédure DE DémarrageRaccorder le tuyau haute pression C à la Sortiede la pompe Section Produits chimiques et solvants De nettoyageEntretien MoteurVérification DU Niveau D’HUILE PompeNettoyage du filtre de l’admission d’eau Méthode DE Vidange DE L’HUILE DE LA PompeLaveuse haute pression Retrait des pneuRangement Glisser le collet hors de l’essieu et retirer le pneuRéparations AccessoiresInformation SUR LES Réparations Garantie limitéeFrançais Glossaire Codes de dépannage Solution ProbableGuide de dépannage Problème CodeCodes de dépannage suite Français Motor Especificaciones de la bombaEspecificaciones CAT 3DX29GsIConserve Estas Instrucciones Definiciones Normas de seguridadInstrucciones de seguridad importantes GravesPeligro Riesgo de explosión o incendio ¿Qué puede suceder? Cómo evitarloPeligro Riesgo Respiratorio asfixia Peligro Riesgo DE Inyección DE Líquido y laceraciónPor ello podría ocasionar Asegúrese de que laLa carne humana y animal Simple Corte ConsultePeligro Riesgo de operación insegura Nota Los tanques de aire PropiedadObserve el flanco para ver la Los compresores y el equipoConserve Estas Instrucciones Para Futuras Consultas Advertencia Riesgo de quemadura químicaOperación InstalaciónEnsamblado de la lavadora a presión Fig Ajustes a la presiónBoquillas para la varilla pulverizadora Fig Cambio DE LAS Boquillas DE LA Varilla PulverizadoraPara Aplicar Productos Químicos Y Solventes Productos químicos y solventes de limpiezaPuesta en marcha Químicos y solventes de limpieza Procedimiento DE Puesta EN MarchaLimpieza, consulte la sección Productos Abra la fuente de aguaMotor ApagadoMantenimiento Suelte el disparador para detener el flujo de aguaPara limpiar el filtro de entrada de agua BombaLimpieza de las boquillas Para Controlar EL AceiteLavadora a presión Para quitar los neumáticosAlmacenamiento BombaReparaciones AccesoriosInformación DE Mantenimiento Póliza de GarantíaGarantía limitada Glosario Para Otras Localidades Llame AL 55 5326Problema Código Guía de detección de problemasCódigos de detección de problemas Código Causa posibleOperación Códigos de detección de problemas continuar Español DeWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD JAN06 Form No. A16505 DP2800 Copyright 2006 DeWALT
Top Page Image Contents