DeWalt DPH3100 instruction manual Maintenance, Engine Pump

Page 13

DANGER: Risk of injury from spray. Engage the

X

trigger lock (X) when gun is not in use to prevent

 

accidental spraying.

13. Adjust spray for the task being performed by changing quick connect nozzle. Refer to Spray Wand Nozzles.

Shutting Down

1.If chemicals were applied, place the chemical hose into a container of clean water and draw clean water through chemical injection system to rinse system thoroughly.

Caution: Risk of property damage Failure to do so could cause damage to the pump.

2.Turn engine off. Refer to the engine instruction manual. Caution: Risk of property damage. Never turn water supply off while pressure washer engine is running or damage to pump will result.

3.Turn water source off.

4.Pull trigger on spray gun to relieve any water pressure in hose or spray gun.

5.Refer to Storage for proper storage procedures.

MAINTENANCE

WARNING: Risk of burning. When performing maintenance, you may be exposed to hot surfaces, water pressure or moving parts that can cause serious injury or death.

WARNING: Risk of fire. Always disconnect, spark plug wire, let the engine cool and release all water pressure before performing any maintenance or repair. The engine contains flammable fuel. Do not smoke or work near open flames while performing maintenance.

To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high

temperatures or dusty conditions, more frequent­ maintenance checks will be required.

Engine

Consult the engine instruction manual for the manu­fac­tur­er's­ recom- mendations for any and all maintenance.

NOTE: The pressure washer frame is equipped with an oil drain hole to help make changing the engine oil easier.

Pump

The high pressure pump is maintenance free and requires no oil, if there is a problem with the pump contact a DeWALT factory service center, a DeWALT authorized service center or other qualified service personnel.

Nozzle Cleaning

If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may develop. If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit supplied and the following instructions:

1.Shut off the pressure washer and turn off the water supply.

2.Pull trigger on gun handle to relieve any water pressure.

3.Disconnect the spray wand from the gun.

4.Remove the high-pressure nozzle from Y

the spray wand. Remove any obstructions with the nozzle cleaning tool (Y) provided and back flush with clean water.

5. Direct water supply into spray wand to

back flush loosened particles for 30 seconds.

6. Reassemble the nozzle to the wand.

English

13

Image 13
Contents Guide Dutilisation Manual de instrucciones Specifications Pump SpecificationsModel Weight Height Width AverageImportant Safety Instructions Definitions Safety GuidelinesDeWALT What can happen How to prevent it What can happen Never leave wand unattended while unit is running Powerful cleaning­ tool Kickback causing seriousHand and arm injury If engine does not start afterWhat can happen How to prevent it Pressure Washer Assembly Fig InstallationFor Future USE Operation Pressure AdjustmentsSpray Wand Nozzles Fig Starting Chemicals and Cleaning SolventsChanging Nozzles on Spray Wand To apply chemicals and solventsConnect high-pressure hose P to pump outlet Start-up ProcedureSolvents Turn the water source onEngine Pump MaintenanceTo Remove Tires To Clean the Water Inlet FilterSTORAGE Engine Pump Pressure WasherLimited Warranty Accessories Service InformationRepairs Date and Place of PurchaseGlossary Troubleshooting Codes Troubleshooting GuideProblem Code Possible SolutionTroubleshooting Codes English Interrupteur moteur Poignée de démarrage Caractéristiques techniques de la pompeMoteur Modèle Sans Entretien DeWALTDéfinitions lignes directrices en Matière de sécurité Fiche techniqueDirectives de sécurité importantes Des blessures gravesCe qui peut se produire Conserver CES DirectivesLaisser environ 127 mm De l’équipement et pro Du matériel déposé contreVoquer une surchauffe et Haute pression dans uneSuite Ce qui peut se produireNe pas utiliser de produit Démarrage correcte pour Suivre la procédure deQui provoquerait ainsi une Au brasCe qui peut se produire Comment l’éviter Avertissement Risque d’éclatementAssemblage de la laveuse haute pression Fig Réglages de la pression FonctionnementBuses du tube de pulvérisation Fig Changement DES Buses SUR LE Tube DE Pulvérisation Produits chimiques et solvants de nettoyageApplication DE Produits Chimiques ET Solvants Démarrage Section Produits chimiques et solvants De nettoyage Procédure DE DémarrageMoteur EntretienPompe Retrait des pneu Nettoyage du filtre de l’admission d’eauRangement Glisser le collet hors de l’essieu et retirer le pneuLaveuse haute pression Accessoires Information SUR LES RéparationsRéparations Garantie limitée Glossaire Guide de dépannage Solution ProbableCodes de dépannage Problème CodeCodes de dépannage suite Français Pistola pulverizadora profe- sional Especificaciones de la bombaMango lateral MotorDefiniciones Normas de seguridad EspecificacionesInstrucciones de seguridad importantes Peligro Riesgo de explosión o incendio Conserve Estas Instrucciones¿Qué puede suceder? Cómo evitarlo Peligro Riesgo Respiratorio asfixia Peligro Riesgo DE Inyección DE Líquido y laceración Peligro Riesgo de operación insegura Puede retroceder, lo que Si no se sigue elLas manos y los brazos Si el motor no arrancaAdvertencia Riesgo DE superficies calientes Advertencia Riesgo de de estallidoAdvertencia Riesgo de quemadura química Ensamblado de la lavadora a presión FigAdvertencia Riesgo DE descarga eléctrica Ajustes a la presión OperaciónBoquillas para la varilla pulverizadora Fig De alta presión P aCambio DE LAS Boquillas DE LA Varilla Pulverizadora Productos químicos y solventes de limpiezaPara Aplicar Productos Químicos Y Solventes Puesta en marchaQuímicos y solventes de limpieza Mantenimiento ApagadoMotor BombaPara quitar los neumáticos Para limpiar el filtro de entrada de aguaAlmacenamiento Accesorios Lavadora a presiónInformación DE Mantenimiento Fecha y lugar de compraPóliza de Garantía ReparacionesGarantía limitada Identificación DEL ProductoCULIACAN, SIN Glosario Códigos de detección de problemas Guía de detección de problemasProblema Código Código Causa posibleCódigos de detección de problemas continuar Español Español OCT07 Part No. N001238 DPH3100 Copyright 2007 D eWALT EWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD