DeWalt DPH3100 To Clean the Water Inlet Filter, To Remove Tires, STORAGE Engine Pump

Page 14

English

7.Reconnect spray wand to gun then turn on water supply.

8.Start pressure washer and place spray wand into high pressure setting to test.

To Clean the Water Inlet Filter

This filter screen (U) should be checked periodically and cleaned if necessary.

1. Remove the filter screen (U) by grasping the

end and removing it from water inlet of pump.

2. Clean filter by flushing it with water on both sides.

3. Reinsert filter into water inlet of pump. Cone

U

side faces out.

 

NOTE: Do not operate pressure washer without

 

flter properly installed.

 

To Remove Tires

1. Using a 1/8" hex head wrench loosen set screw in hub collar.

2. Slide hub collar from axle and remove the tire.

sTORAGE Engine

Consult the engine instruction manual for the manu­fac­tur­er's­ recommendations for storage.

Pump

The manufacturer recommends using a pump protector/winter- izer, such as DeWALT winterizer (DP80) when storing the unit for more than 30 days and/or when freezing temperatures are expected. DeWALT winterizer (DP80) is availabe at the store where the pressure washer was purchased. If a pump protector/

winterizer is not available, RV antifreeze can be used as outlined in the following steps.

NOTE: Using a pump protector/ winterizer or RV antifreeze helps to provide proper lubrication to the internal seals of the pump regard- less of temperature or environment.

1.Obtain a funnel, 6 oz. (170 mL) of RV antifreeze and 16–36" (40–91cm) of garden hose with a male hose connector attached to one end.

CAUTION: Risk of property damage. Use only RV antifreeze. Any other anti­freeze­ is corrosive and can damage pump.

2. Disconnect spark plug wire.

3. Connect length of garden hose to water inlet of pump.

4.

Add RV antifreeze to hose as

 

shown.

 

 

5.

Pull engine starter

rope

slow-

 

ly several times until anti­freeze­

 

comes out of high-pressure hose

 

connec­tion­ of pump.

 

 

6.

Remove garden

hose

from

 

water inlet of pump.

 

 

7. Reconnect spark plug wire.

Pressure Washer

1.Drain all water from high- pressure hose, coil it and store it in cradle of the pressure washer handle.

2.With nozzle pointed down and the spray gun and wand in a

vertical position, squeeze trigger to drain all water from spray gun and wand. Store in gun holder.

14

Image 14
Contents Guide Dutilisation Manual de instrucciones Model Weight Height Width Pump SpecificationsSpecifications AverageDeWALT Definitions Safety GuidelinesImportant Safety Instructions What can happen How to prevent it What can happen Never leave wand unattended while unit is running Hand and arm injury Kickback causing seriousPowerful cleaning­ tool If engine does not start afterWhat can happen How to prevent it For Future USE InstallationPressure Washer Assembly Fig Spray Wand Nozzles Fig Pressure AdjustmentsOperation Changing Nozzles on Spray Wand Chemicals and Cleaning SolventsStarting To apply chemicals and solventsSolvents Start-up ProcedureConnect high-pressure hose P to pump outlet Turn the water source onMaintenance Engine PumpSTORAGE Engine Pump To Clean the Water Inlet FilterTo Remove Tires Pressure WasherRepairs Accessories Service InformationLimited Warranty Date and Place of PurchaseGlossary Problem Code Troubleshooting GuideTroubleshooting Codes Possible SolutionTroubleshooting Codes English Moteur Caractéristiques techniques de la pompeInterrupteur moteur Poignée de démarrage Modèle Sans Entretien DeWALTDirectives de sécurité importantes Fiche techniqueDéfinitions lignes directrices en Matière de sécurité Des blessures gravesLaisser environ 127 mm Conserver CES DirectivesCe qui peut se produire Voquer une surchauffe et Du matériel déposé contreDe l’équipement et pro Haute pression dans uneCe qui peut se produire SuiteNe pas utiliser de produit Qui provoquerait ainsi une Suivre la procédure deDémarrage correcte pour Au brasAvertissement Risque d’éclatement Ce qui peut se produire Comment l’éviterAssemblage de la laveuse haute pression Fig Buses du tube de pulvérisation Fig FonctionnementRéglages de la pression Application DE Produits Chimiques ET Solvants Produits chimiques et solvants de nettoyageChangement DES Buses SUR LE Tube DE Pulvérisation Démarrage Procédure DE Démarrage Section Produits chimiques et solvants De nettoyagePompe EntretienMoteur Rangement Nettoyage du filtre de l’admission d’eauRetrait des pneu Glisser le collet hors de l’essieu et retirer le pneuRéparations Accessoires Information SUR LES RéparationsLaveuse haute pression Garantie limitée Glossaire Codes de dépannage Solution ProbableGuide de dépannage Problème CodeCodes de dépannage suite Français Mango lateral Especificaciones de la bombaPistola pulverizadora profe- sional MotorInstrucciones de seguridad importantes EspecificacionesDefiniciones Normas de seguridad ¿Qué puede suceder? Cómo evitarlo Conserve Estas InstruccionesPeligro Riesgo de explosión o incendio Peligro Riesgo Respiratorio asfixia Peligro Riesgo DE Inyección DE Líquido y laceración Peligro Riesgo de operación insegura Las manos y los brazos Si no se sigue elPuede retroceder, lo que Si el motor no arrancaAdvertencia Riesgo de de estallido Advertencia Riesgo DE superficies calientesAdvertencia Riesgo DE descarga eléctrica Ensamblado de la lavadora a presión FigAdvertencia Riesgo de quemadura química Boquillas para la varilla pulverizadora Fig OperaciónAjustes a la presión De alta presión P aProductos químicos y solventes de limpieza Cambio DE LAS Boquillas DE LA Varilla PulverizadoraPuesta en marcha Para Aplicar Productos Químicos Y SolventesQuímicos y solventes de limpieza Motor ApagadoMantenimiento BombaAlmacenamiento Para limpiar el filtro de entrada de aguaPara quitar los neumáticos Información DE Mantenimiento Lavadora a presiónAccesorios Fecha y lugar de compraGarantía limitada ReparacionesPóliza de Garantía Identificación DEL ProductoCULIACAN, SIN Glosario Problema Código Guía de detección de problemasCódigos de detección de problemas Código Causa posibleCódigos de detección de problemas continuar Español Español EWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD OCT07 Part No. N001238 DPH3100 Copyright 2007 D eWALT