Agilent Technologies 5951-2827, 5951-2826 manual Constant Resistance CR, 6060B, Constant Voltage CV

Page 73

Table 5-1. Remote Programming Ranges (continued)

Function

HPSL Command

(Short Form)

Range of Values

Constant Resistance (CR)

Set Range

Low Range

Middle Range

High Range

Set Main Level

Low Range

Middle Range

High Range

Set Slew Rate

"RES:RANG value"

’RES value"

6060B

³0 or £ 1 W >1 W and £ kW >1 kW and £ kW

0 to 1 W

1W to 1 kW

10W to 10 kW

6063B

³0 and £ 24 W

£24 W and £ 24 kW >24 kW and £ 240 kW

0 to 24 W

24W to 24 kW

240W to 240 kW

Low Range

Middle/High Range

Set Transient Level

*Set Triggered Level

Constant Voltage (CV)

Set Main Level

Set Slew Rate

Set Transient Level

*Set Triggered Level

Transient Operation

Set Frequency

Set Duty Cycle

*Set Pulse Width

"VOLT: SLEW value" "CURR:SLEW value"

"RES:TLEV value" "RES:TRIG value"

"VOLT value"

"VOLT:SLEW value" "VOLT:TLEV value" "VOLT:TRIG value"

"TRAN:FREQ value" "TRAN:DCYC value"

"TRAN:TWID value"

Same as CV slew rate

Same as CC slew rate

Same as main CR level

Same as main CR level

6060B	6063B
0 to 60 V	0 to 240 V
1000 to 5,000,000 V/s	4000 to 2,000,000 V/s

Same as main CV level

Same as main CV level

0.25 to 10000 Hz

3 to 97% (0.25 Hz to 1 kHz

6-94% (1 kHz-10 kHz)

0.00005 to 4 seconds

Current Protection

*Set Current Level

*Set Delay Time

	6060B	6063B
"CURR:PROT value"	0 to 61.2 A	0 to 10.2 A
"CURR:PROT:DEL value"		0 to 60 seconds

*Can only be programmed remotely via the GPIB.

Remote Operation 73

Image 73

Contents Operating Manual Agilent Part No Microfiche Part No Updated AprilCertification Safety Summary Symbol Description Safety SummaryHerstellerbescheinigung Manufacturer’s DeclarationPrinting History Table of Contents Remote Operation Local OperationCalibration Considerations for Operating in Constant Resistance Mode Reader Path What’s In This ManualOptions General InformationSpecifications Safety RequirementsModes Continuous Mode Regulation Constant Resistance Mode RangesPulsed Mode 6060B 6063BCurrent Readback Resolution Supplemental Characteristics 6060B 6063BTemperature Coefficient Bandwidth Maximum Readback CapabilityMaximum VA Peak Inrush Current 2.5 a typical Supplemental CharacteristicsCurrent Slew Rate Rate # High Range Step Low Range Step Transition TimeOvershoot Resistance Slew RateModel 6063B Range Transient Current Level With unit on 6060B 6063B 10%With unit off WidthPage Front Panel Description IntroductionRemote Programming Operation OverviewProgrammable Features Local/Remote ControlConstant Current CC Mode Modes of OperationSoftware Current Limit Triggered Current LevelSlew Rate Constant Resistance CR ModeImmediate Resistance Level Triggered Resistance Level Constant Voltage CV ModeTransient Resistance Level Triggered Voltage Level Immediate Voltage LevelTransient Voltage Level Transient OperationPulsed Transient Operation Hpsl Command DescriptionSelects pulsed transient operation Selects the external trigger inputSets pulse width to 1 millisecond Selects the external trigger input sourceTriggering a transient pulse Triggering a preset levelToggling Slew Rate And Minimum Transition TimeRisetime Transition Limitation Input Current, Voltage, and Power MeasurementTransition Times and Slew Rates Short On/OffReading Remote Programming Errors Saving and Recalling SettingsInput On/Off Status ReportingResetting Latched Protection Protection FeaturesOvervoltage OvercurrentOverpower Control ConnectorOvertemperature Reverse VoltageMonitor Outputs FaultExternal Programming Input Port On/Off Inspection Turn-On Checkout Location and CoolingCheck Line Voltage Line Voltage Fuse Agilent Part No Voltage Select SwitchesGpib Errors Input Errors Display Description Connect The Power CordError Turn-On/SelftestGpib Connector Power TestController Connection Wire Size Strip back Rear Panel Connectors and SwitchesGpib Address AWGInput Binding Post Control Connector +S and -S Pins 3IM and VM CommonSense Switch Trigger ConnectorApplication Connections Parallel Connections Maximum Wire Lengths to Limit Voltage DropsZero-Volt Loading Connections 11. Local Sensing 13. Parallel Operation Page Local Operation Front Panel Controls and Indicators DescriptionControls and Indicators Description Function Keys Local Control Overview ∙ Short on Using The Function KeysTurning the Input On/Off Recommended Programming Sequence Setting CC Values Setting the Mode of OperationCC Programming Ranges Function Key DisplayExamples Setting CR Values Examples Setting CV Values Function Key Display Range of Values Continuous Pulse Train Programming RangesShorting The Input Using The System KeysDisplaying Error Codes Setting The Electronic Load’s Gpib AddressChanging Wake-up Settings Factory Default Settings Function 6060B 6063BRecalling the Factory Default Values Gpib Address Enter/Output StatementsOutput EnterRemote Programming Commands Sending a Remote CommandGetting Data Back Output 705 MEASCURR?Ranges ModesTransient levels Slew RatesRemote Programming Flowchart Sheet Remote Programming Flowchart Sheet CV Mode Example CC Mode ExampleCR Mode Example Pulsed Transient Operation Example Continuous Transient Operation ExampleOutput 705TRAN on Output 705INPUT on Hpsl Command Short FormRemote Programming Ranges Function Constant Current CC6060B Constant Resistance CRConstant Voltage CV Transient OperationPage Example Programs Equipment Characteristics Recommended ModelEquipment Required Equipment Required for CalibrationCalibration Commands Example Program Calibration FlowchartsCalibration Information 6060B 6063B Supply Shunt Values SettingsCalibration Flowchart Calibration Flowchart Calibration Flowchart Pause Program ListingWait END ifPrint Voltage Calibration Pause SubendElse Line ExplanationPage Considerations For Operating In Constant Resistance Mode Considerations For Operating In Constant Resistance ModeConsiderations For Operating In Constant Resistance Mode Index IndexIndex 24, 25, 26 Index Agilent Sales and Support Office Agilent Sales and Support OfficesManual Updates