Elo TouchSystems IntelliTouch SecureTouch manual Agency Approvals

Page 75

Altitude

Chemical

Resistance

Electrostatic

Protection

Agency

Approvals

UL Compliance

Fire Retardation

FCC Compliance

Operating: 10,000 ft (3,048 m).

Storage/transport: 50,000 ft (15,240 m).

The touchactive area of the touchscreen is resistant to all chemicals that do not affect glass, such as:

Acetone

Toluene

Methyl ethyl ketone Isopropyl alcohol Methyl alcohol Ethyl acetate Ammonia-based glass cleaners Gasoline

Kerosene

Vinegar

When tested per IEC 801-2 (150 pF and 150 Ω ), the touchscreen shall withstand 20 air discharges of 15 kV, distributed randomly across the active area of the touchscreen.

IntelliTouch touchscreens are UL-Recognized Components. UL file no. E162681

Meets the requirements of UL94HB.

Systems incorporating Elo touchscreens, controllers and cables have been approved to FCC Class "B" compliance.

B-63

Image 75

Contents Page Elo IntelliTouch /SecureTouch Touchscreen Guide Disclaimer Page Intellitouch 10-YEAR Warranty Page Table of Contents Index List of Figures Viii List of Tables Page Introduction Intellitouch TechnologyIntelliTouch Touchscreen IntelliTouch TouchscreenIntelliTouch controller IntelliTouch ControllerAgency Approvals Driver SoftwareWork Area Safety InformationGetting Started Design Considerations for CRTs and LCDsProtective Clothing Bezel design Bezel DesignCRT Integration Safety InformationSuggested Tools Definition of TermsTypical IntelliTouch Touchscreen Installation Summary of Installation StepsUnpacking the Touchscreen Testing the MonitorIncoming Inspection Disassembling the MonitorDischarge the CRT Remove the Back CaseRemove the Electronic Chassis 14I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Remove the CRT Verify Touchscreen Fit Page Attaching the Touchscreen Proper placement of adhesive tape to the touchscreen Spacing the CRT from the Bezel Installing the Controller Touchscreen Cabling System for Internal Serial Controller Internal Serial Controller 2500SP4 Pins Signal Function 24I n t e l l i T o u c h / S e c u r e T o u c h G u i d e External Serial Controller 26I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Internal USB Controller 2500U Internal USB Controller 2500U28I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Reassembling the Monitor Routing the Touchscreen CablesProper Sealing Improper Sealing Sealing the MonitorSealing Material Selection System EvaluationProper Bezel Mounting Improper Bezel Mounting LCD Integration Unpacking the Touchscreen Definition of Terms Disassembling the LCD MonitorTools and Equipment Required Parts for Serial ConnectionRequired Parts for USB Connection Optional Parts for USB Connection Optional Parts for Serial ConnectionRemoving the LCD Removing the Rear CaseDetermining Touchscreen Fit Mounting the Touchscreen Attaching double-sided adhesive tape to the touchscreen Spacing the LCD from the Bezel Sealing10 2500S Internal Serial Controller 11 2500U USB controller Parasitic Tap of 5Vdc Power12 DC to DC converter Parasitic Tap of 7-30Vdc DC to DC converterModifying the Case for USB Output Modifying the Case for Serial Output13 Horizontal escutcheon plate Re-assembling the Display48I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Troubleshooting Process Troubleshooting GuideSoftware Troubleshooting Display ProblemsVideo Alignment Problems Hardware TroubleshootingSerial Controller Using the Comdump UtilityByte Byte DescriptionP2 Pins DB25 Host Signal SourceRS-232 Connections Power Connections Touchscreen and Touchscreen Cables Figure A.2 Transducer and Wedge AssemblyIC1 Cable EC2 Cable2x6 Male Header DB9 Male Function IntelliTouch Serial Controllers Diagnostic LEDsDiagnostic Codes IntelliTouch Serial Controller 2500SAA Bit Value hex Description Figure A.4 DB9 and DB25 Connector Pin Positions DB9 and DB25 Connector Pin PositionsSpecifications Environmental IntelliTouch TouchscreensMechanical OpticalUL Compliance Fire Retardation FCC Compliance Agency ApprovalsPhysical Characteristics IntelliTouch 2500U USB ControllerElectrical Touchscreen Connector Power Connector, P4 P2 pin number Signal name Standard wire color Signal name P4 pin Signal function Signal name P3 pin Signal functionLED State Function LED Diagnostic CharacteristicsAgency Approvals LED Blink Rate FunctionFigure B.4 2500U USB Controller, top view 2500U USB Controller DrawingsFigure B.6 2500U USB Controller, bottom-view Environments IntelliTouch 2500S Serial Controller72I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Parameter Value Applicable Signals EIA-232 subsec Signal Name DB-9 P2 pin Sourced by Signal FunctionBoard mounted Cable applied Header Plug Jumper Function Jumper Settings76I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Figure B.11 2500S Serial Controller, top view DrawingsFigure B.13 2500S Serial Controller Part Number Description ELO Part NumbersCables Stylus 82I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Glossary Page Glossary-85 Page Glossary-87 Vertical Refresh Rate-See Refresh Rate Index Page Page