Elo TouchSystems IntelliTouch SecureTouch manual Internal USB Controller 2500U

Page 39

Internal USB Controller (2500U)

The mounting holes for the 2500U USB controller are sized for 0.156-inch (4 mm) snap-in standoffs. All current IntelliTouch touchscreens have a cable that mates directly with the male header (P3) on the controller. The controller must be powered from inside the monitor.

Figure 2.6 Internal USB Controller (2500U)

CAUTION Before making any attempt to power the controller from any monitor power source, you should confirm the installation with your monitor supplier. Failure to observe this caution may destroy the monitor or seriously impair monitor performance.

Follow these steps to install the IntelliTouch 2500U USB controller:

1Evaluate the monitor for proper positioning of the controller. Make sure there is sufficient space for cable headers.

2Evaluate the back case of the monitor to determine the best position for the USB connector. There are two possible configurations for installing the USB controller.

•Configuration 1: mount the controller card so the USB connector is flush with the back of the monitor.

•Configuration 2: mount the controller inside the controller inside the monitor and use the Elo USB cable pack (See “Elo Part Numbers” on page 79) to mount a USB connector.

2-27

Image 39

Contents Page Elo IntelliTouch /SecureTouch Touchscreen Guide Disclaimer Page Intellitouch 10-YEAR Warranty Page Table of Contents Index List of Figures Viii List of Tables Page Introduction Intellitouch TechnologyIntelliTouch Touchscreen IntelliTouch TouchscreenIntelliTouch controller IntelliTouch ControllerAgency Approvals Driver SoftwareWork Area Safety InformationGetting Started Design Considerations for CRTs and LCDsProtective Clothing Bezel design Bezel DesignCRT Integration Safety InformationSuggested Tools Definition of TermsTypical IntelliTouch Touchscreen Installation Summary of Installation StepsUnpacking the Touchscreen Testing the MonitorIncoming Inspection Disassembling the MonitorDischarge the CRT Remove the Back CaseRemove the Electronic Chassis 14I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Remove the CRT Verify Touchscreen Fit Page Attaching the Touchscreen Proper placement of adhesive tape to the touchscreen Spacing the CRT from the Bezel Installing the Controller Touchscreen Cabling System for Internal Serial Controller Internal Serial Controller 2500SP4 Pins Signal Function 24I n t e l l i T o u c h / S e c u r e T o u c h G u i d e External Serial Controller 26I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Internal USB Controller 2500U Internal USB Controller 2500U28I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Reassembling the Monitor Routing the Touchscreen CablesProper Sealing Improper Sealing Sealing the MonitorSealing Material Selection System EvaluationProper Bezel Mounting Improper Bezel Mounting LCD Integration Unpacking the Touchscreen Definition of Terms Disassembling the LCD MonitorTools and Equipment Required Parts for Serial ConnectionRequired Parts for USB Connection Optional Parts for USB Connection Optional Parts for Serial ConnectionRemoving the LCD Removing the Rear CaseDetermining Touchscreen Fit Mounting the Touchscreen Attaching double-sided adhesive tape to the touchscreen Spacing the LCD from the Bezel Sealing10 2500S Internal Serial Controller 11 2500U USB controller Parasitic Tap of 5Vdc Power12 DC to DC converter Parasitic Tap of 7-30Vdc DC to DC converterModifying the Case for USB Output Modifying the Case for Serial Output13 Horizontal escutcheon plate Re-assembling the Display48I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Troubleshooting Process Troubleshooting GuideSoftware Troubleshooting Display ProblemsVideo Alignment Problems Hardware TroubleshootingSerial Controller Using the Comdump UtilityByte Byte DescriptionP2 Pins DB25 Host Signal SourceRS-232 Connections Power Connections Touchscreen and Touchscreen Cables Figure A.2 Transducer and Wedge AssemblyIC1 Cable EC2 Cable2x6 Male Header DB9 Male Function IntelliTouch Serial Controllers Diagnostic LEDsDiagnostic Codes IntelliTouch Serial Controller 2500SAA Bit Value hex Description Figure A.4 DB9 and DB25 Connector Pin Positions DB9 and DB25 Connector Pin PositionsSpecifications Environmental IntelliTouch TouchscreensMechanical OpticalUL Compliance Fire Retardation FCC Compliance Agency ApprovalsPhysical Characteristics IntelliTouch 2500U USB ControllerElectrical Touchscreen Connector Power Connector, P4 P2 pin number Signal name Standard wire color Signal name P4 pin Signal function Signal name P3 pin Signal functionLED State Function LED Diagnostic CharacteristicsAgency Approvals LED Blink Rate FunctionFigure B.4 2500U USB Controller, top view 2500U USB Controller DrawingsFigure B.6 2500U USB Controller, bottom-view Environments IntelliTouch 2500S Serial Controller72I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Parameter Value Applicable Signals EIA-232 subsec Signal Name DB-9 P2 pin Sourced by Signal FunctionBoard mounted Cable applied Header Plug Jumper Function Jumper Settings76I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Figure B.11 2500S Serial Controller, top view DrawingsFigure B.13 2500S Serial Controller Part Number Description ELO Part NumbersCables Stylus 82I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Glossary Page Glossary-85 Page Glossary-87 Vertical Refresh Rate-See Refresh Rate Index Page Page