Elo TouchSystems IntelliTouch SecureTouch manual Installing the Controller

Page 33

During the spacer selection process, you may have to install the CRT with the touchscreen attached in the bezel several times. To prevent the CRT from dislodging the spacers, temporarily insert plastic tie wraps or toothpicks as guides in the mounting post holes. After selecting the correct spacers, discard the guides and fix the spacers more securely in place with the adhesive "doughnuts" provided in the Touchscreen Installation Kit.

When spacers for the desired gap have been selected, install the CRT. Make sure you have previously reinstalled the degaussing coil. Select a screw that is long enough to compensate for the spacer thickness (provides at least three full turns into the mounting post threads) but not so long as to penetrate the surface of the bezel. Over-tightening the screws may strip or split the mounting posts.

Installing the Controller

Elo offers IntelliTouch USB or serial (RS-232) controllers which are typically installed internal to the display.

Before installing an IntelliTouch controller, you need to ensure the following design conditions:

Ensure there is space for the controller and the cable headers.

Note that cable routing may contribute to noise and crosstalk. Make sure the controller is placed away from voltage sources.

Ensure there is space for an internal DC-to-DC converter or AC power supply if either is required.

Verify power source and check specs for adequate power. The 2500 controllers use +5V@60 mA ±5% regulated.

Ensure sufficient electromagnetic Interference (EMI) suppression. Installing a touchscreen and controller will affect the EMI characteristics of the display.

Note: Ensure sufficient heat dissipation. The IntelliTouch serial controller dissipates some heat (less than 1 watt). A typical power supply, if required, may dissipate several watts more. This places an additional load on the cooling system of the display. The available locations to mount a controller and power supply may also affect the cooling system of the display. Only applicable if you are not using AC-to-DC power supply.

Ensure controller can be mounted securely to metal bracket and grounded.

Ground at least one mounting hole, but for best EMI characteristics, ground all four mounting holes.

2-21

Image 33
Contents Page Elo IntelliTouch /SecureTouch Touchscreen Guide Disclaimer Page Intellitouch 10-YEAR Warranty Page Table of Contents Index List of Figures Viii List of Tables Page Introduction Intellitouch TechnologyIntelliTouch Touchscreen IntelliTouch TouchscreenIntelliTouch controller IntelliTouch ControllerAgency Approvals Driver SoftwareWork Area Safety InformationGetting Started Design Considerations for CRTs and LCDsProtective Clothing Bezel design Bezel DesignCRT Integration Safety InformationSuggested Tools Definition of TermsTypical IntelliTouch Touchscreen Installation Summary of Installation StepsIncoming Inspection Testing the MonitorDisassembling the Monitor Unpacking the TouchscreenDischarge the CRT Remove the Back CaseRemove the Electronic Chassis 14I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Remove the CRT Verify Touchscreen Fit Page Attaching the Touchscreen Proper placement of adhesive tape to the touchscreen Spacing the CRT from the Bezel Installing the Controller Touchscreen Cabling System for Internal Serial Controller Internal Serial Controller 2500SP4 Pins Signal Function 24I n t e l l i T o u c h / S e c u r e T o u c h G u i d e External Serial Controller 26I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Internal USB Controller 2500U Internal USB Controller 2500U28I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Reassembling the Monitor Routing the Touchscreen CablesProper Sealing Improper Sealing Sealing the MonitorSealing Material Selection System EvaluationProper Bezel Mounting Improper Bezel Mounting LCD Integration Unpacking the Touchscreen Definition of Terms Disassembling the LCD MonitorTools and Equipment Required Parts for Serial ConnectionRequired Parts for USB Connection Optional Parts for USB Connection Optional Parts for Serial ConnectionRemoving the LCD Removing the Rear CaseDetermining Touchscreen Fit Mounting the Touchscreen Attaching double-sided adhesive tape to the touchscreen Spacing the LCD from the Bezel Sealing10 2500S Internal Serial Controller 11 2500U USB controller Parasitic Tap of 5Vdc Power12 DC to DC converter Parasitic Tap of 7-30Vdc DC to DC converterModifying the Case for USB Output Modifying the Case for Serial Output13 Horizontal escutcheon plate Re-assembling the Display48I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Troubleshooting Process Troubleshooting GuideSoftware Troubleshooting Display ProblemsVideo Alignment Problems Hardware TroubleshootingSerial Controller Using the Comdump UtilityByte Byte DescriptionP2 Pins DB25 Host Signal SourceRS-232 Connections Power Connections Touchscreen and Touchscreen Cables Figure A.2 Transducer and Wedge AssemblyIC1 Cable EC2 Cable2x6 Male Header DB9 Male Function IntelliTouch Serial Controllers Diagnostic LEDsDiagnostic Codes IntelliTouch Serial Controller 2500SAA Bit Value hex Description Figure A.4 DB9 and DB25 Connector Pin Positions DB9 and DB25 Connector Pin PositionsSpecifications Mechanical IntelliTouch TouchscreensOptical EnvironmentalUL Compliance Fire Retardation FCC Compliance Agency ApprovalsPhysical Characteristics IntelliTouch 2500U USB ControllerElectrical Touchscreen Connector Power Connector, P4 P2 pin number Signal name Standard wire color Signal name P4 pin Signal function Signal name P3 pin Signal functionAgency Approvals LED Diagnostic CharacteristicsLED Blink Rate Function LED State FunctionFigure B.4 2500U USB Controller, top view 2500U USB Controller DrawingsFigure B.6 2500U USB Controller, bottom-view Environments IntelliTouch 2500S Serial Controller72I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Parameter Value Applicable Signals EIA-232 subsec Signal Name DB-9 P2 pin Sourced by Signal FunctionBoard mounted Cable applied Header Plug Jumper Function Jumper Settings76I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Figure B.11 2500S Serial Controller, top view DrawingsFigure B.13 2500S Serial Controller Part Number Description ELO Part NumbersCables Stylus 82I n t e l l i T o u c h / S e c u r e T o u c h G u i d e Glossary Page Glossary-85 Page Glossary-87 Vertical Refresh Rate-See Refresh Rate Index Page Page