Barco R9002120 Location and Function of Controls, Rear Panel Terminology, Front Panel Terminology

Page 11

Location and Function of Controls

2						LOCATION AND FUNCTION OF CONTROLS
2



Rear Panel Terminology

RS232IN

RS232OUT

IR

COMM PORT

R

G(S)

B

S-VIDEO

(800 peripherals) REMOTE

S

VIDEO

R- Y

Y(S )

B -Y

1

2

3

4

5

6

7

8

1

2

RS232IN	6	RGB-S IN or (R-Y)Y(B-Y)-S IN (4x BNC connector):
Connection between the projector and an IBM PC (or	6	RGB-S in : allows a character generator, microcomputer,
compatible) or MAC (RS422) for remote computer control		video camera, etc. having analog RGB output to be con-
and data communication.		nected to the projector.
RS232OUT		Line inputs: - signals RED-GREEN-BLUE
Used to connect to the next projector, RS232IN plug		- COMPOSITE sync. signal
(communication link for PC or MAC to the next projector)

3	IR sensor
3	receiver for control signals transmitted from the RCU.
4	Communication port (800 peripherals)
4	* allows communication between the RCVDS switcher and
	the projector.
	* allows connection of a remote IR receiver unit to the
	projector.
	* allows connection of an IRIS 800 to converge the image
	automatically.
5	IR Remote
5	remote input for wired remote control

Front Panel Terminology

(R-Y)Y(B-Y)-S IN (component in):allows to connect e.g. a professional VCR having component outputs to the projec- tor.

Line inputs	- signals RED-LUMA, LUMA, BLUE-LUMA
	- COMPOSITE sync. signal

VIDEO IN (Composite video, 1x BNC connector): allows a

7 video tape recorder, video camera, color receiver/monitor, etc. having video line output to be connected to the projector.

S-VIDEO IN: Separated Y/C (luma-chroma) signal inputs

8 and outputs for higher quality playback of Super VHS signals (4-pin S-VIDEO connector).

1

AUTODIAGNOSIS DISPLAY

1 LED indication for service purposes.

-CONV

+9V +17V

+210V -9V +30V

-17V +HTHD +CONV

STANDBY

HOLD DOWN EHT

SF

COINC

HOLD DOWN HD

2 3 4

	3	POWER (MAINS) INPUT: Connect the supplied ac power
	3	(mains) cord here and to wall the outlet.
		(mains) cord here and to wall the outlet.
	4	IR SENSOR
	4	receiver for control signals transmitted from the RCU700.
		receiver for control signals transmitted from the RCU700.


2	POWER (MAINS) SWITCH : press the switch to turn the
	projector ON.
	Depending on the hardware set-up of the projector during
	installation, the projector switches to ‘standby’ or to
	‘operational mode’. If in standby, the standby led in the
	autodiagnosisdisplay lights up.
5975977 BARCODATA 708 260597			2-1

Image 11

Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn repacking On installationOn cleaning On servicingFront Panel Terminology Location and Function of ControlsRear Panel Terminology RCU control panel terminology Gaining accessAdjustexit Control panel terminology a. The local keypadLocation and Function of Controls Location and Function of Controls Connections Power mains cord connectionSwitching on/off Signal input connection to the projectorVideo input selection Connecting a Composite Video sourceSource No Projector input Press digit button Input selection Connecting a S-Video or Video source to portRgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync YYB-YS orR-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RGB3S or RG3sB input selectionYYB-Y3S or R-YY3sB-Y input selection Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Remote controlControlling Battery installation in the RCUProjector address How to use the RCUHow to display a projector address? Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeInternal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select Line Doubler optionPort 2 S-Video/Video PeakingGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Raster Shift AdjustmentProjected raster Crt faceplate borderLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeData Projector Set-upIdentification Change Language Change passwordTotal Run Time Baudrate Power up modeChange Projector Address Change baudrateMemory Management BARCOlogoMemory management Barco LogoDeleting block by block Copy a blockDeletion of blocks Undo ALL Settings to Midpos All settings to midpositionUndo all settings to midpos ALL Settings to MidposUndo green convergence mid Convergence midUndo R & B convergence mid Green convergence midG2 Adjustment Common SettingsG2 Adjustment Common SettingsProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode Invalid Code entry End of ad- just range Enter Password Text on Text offI2C error Addr FH3 Fh= 15.6 kHz Fv= 050 HzStarting Rcvds com Munication ErrorIris commu Nication Error Projector Will Switch offOptions Adapter and communication cables Magik Interface Orbiting KitLine Doubler Kit Ceiling mount CM50Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Barcodata 708 Insert Card