Barco R9002120 manual How to program an address into the RCU?

Page 23

Controlling

To continue using the RCU, it is necessary to enter an address with the digit buttons (address between 0 and 9). For example : if the Address key displays projector address 003, the press "3" digit button on the RCU to set the RCU's address to match the projector's address. Do not press digit 003. This will address the remote to '0' and control all projectors in the room.

How to program an address into the RCU?

Press the ADDRESS key (recessed key on the RCU) with a pencil and enter the address with the digit buttons. That address can be any digit between 0 and 9.

Input selection

Source No

Projector input

Press button

 

 

 

1

Comp. Video

1

2

S-Video/Comp. Video1

2

3

RGBS or RGsB

3

3

RGB3S or RG3sB

4

3

(R-Y)Y(B-Y)S or

 

 

(R-Y)Ys(B-Y)

5

3

(R-Y)Y(B-Y)3S or

 

 

(R-Y)Y3s(B-Y)

6

 

 

 

Two possible ways of selecting an input :

a)With the digit buttons on the RCU, it is possible to select one of the four input sources, Video, S-Video, RGsB or RGBS, RG3sB or RGB3S, (R-Y)Ys(B-Y) or (R-Y)Y(B-Y)S, (R-Y)Y3s(B-Y) or (R-Y)Y(B- Y)3S.

b)With the local keypad :

press first the ADJUST key to display the General access menu.

control disk to the left or to the right to move the cursor to the left and to the right.

Press ENTER to confirm your selection.

When a valid and available source is selected, there will be informa- tion displayed on the screen about that source. This information includes :

-Source number

-Horizontal frequency

-Vertical frequency

Source 2

Fh= 15.6 kHz

Fv= 50 Hz

When the entry is a non valid source number, a warning appears on the screen : 'input not available'.

WARNING

input not available

When a valid source number is selected, the projector will display this source or it will wait on the selected source number until the source becomes available. A message 'source not available' will be dis- played for a short time.

ADJUSTEXIT

STANDBYENTER

Use the control disk to highlight the desired source number. Push the control disk up or down to move the cursor up and down, push the

 

GENERAL ACCESS

 

 

SHARPNESS

 

 

TINT

5

6

COLOR

3

4

BRIGHTNESS

1

2

CONTRAST

Enter ADJUST

Select with

,

 

or

then <ENTER>.

<EXIT> to return

WARNING

source not available

5975977 BARCODATA 708 260597

 

4-3

 

Image 23
Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn repacking On installationOn cleaning On servicingFront Panel Terminology Location and Function of ControlsRear Panel Terminology RCU control panel terminology Gaining accessAdjustexit Control panel terminology a. The local keypadLocation and Function of Controls Location and Function of Controls Connections Power mains cord connectionSwitching on/off Signal input connection to the projectorVideo input selection Connecting a Composite Video sourceSource No Projector input Press digit button Input selection Connecting a S-Video or Video source to portRgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync YYB-YS orR-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RGB3S or RG3sB input selectionYYB-Y3S or R-YY3sB-Y input selection Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Remote controlControlling Battery installation in the RCUProjector address How to use the RCUHow to display a projector address? Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeInternal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select Line Doubler optionPort 2 S-Video/Video PeakingGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Raster Shift AdjustmentProjected raster Crt faceplate borderLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeData Projector Set-upIdentification Change Language Change passwordTotal Run Time Baudrate Power up modeChange Projector Address Change baudrateMemory Management BARCOlogoMemory management Barco LogoDeleting block by block Copy a blockDeletion of blocks Undo ALL Settings to Midpos All settings to midpositionUndo all settings to midpos ALL Settings to MidposUndo green convergence mid Convergence midUndo R & B convergence mid Green convergence midG2 Adjustment Common SettingsG2 Adjustment Common SettingsProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode Invalid Code entry End of ad- just range Enter Password Text on Text offI2C error Addr FH3 Fh= 15.6 kHz Fv= 050 HzStarting Rcvds com Munication ErrorIris commu Nication Error Projector Will Switch offOptions Adapter and communication cables Magik Interface Orbiting KitLine Doubler Kit Ceiling mount CM50Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Barcodata 708 Insert Card