Barco R9002120 manual Adjustment mode, Adjustexit Standbyenter

Page 25

Safety Instructions

5	START UP OF THE ADJUSTMENT MODE

Adjustment mode

All picture geometry and convergence adjustments are made while in the 'Adjustment mode'. Two possible ways to enter the adjustment mode :

a) Using the RCU.

Press the ADJUST key.

The projector displays the path selection menu.

b) Using the local keypad.

Press the ADJUST key.

The projector displays the General access menu.

Use the control disk to highlight enter ADJUST and press ENTER. The path selection menu will be displayed.

ADJUSTEXIT

STANDBYENTER

	GENERAL ACCESS
		SHARPNESS
		TINT
5	6	COLOR
3	4	BRIGHTNESS
1	2	CONTRAST

Enter ADJUST

Select with	,
	or
then <ENTER>.

<EXIT> to return

Note : to adjust the Analog picture control while in the 'Adjustment mode', press the ADJUST key. The next General Access menu will be displayed.

Push the control disk up or down to select the analog control to be adjusted and press the ENTER key to confirm.

When the analog control is adjusted the projector returns automatically to the General access menu. When you want to return to the Adjustment mode, press EXIT, otherwise select quit ADJUST and press ENTER to return to operational mode.

You are now in the 'Adjustment mode'. The control disk is used to make menu selections and also vertical and horizontal adjustments. The ENTER and EXIT keys are used to move forward and backward through the menu structure. The ADJUST key can be used to terminate the adjustment mode while a path selection menu (head menu) is displayed.

There are 5 possible paths to follow once in the Adjustment mode. They are :

INSTALLATION - Installation should be selected if the projector has been relocated and/or a different screen size is desired.

When selecting 'Installation', the user or operator will be warned to call a qualified technician to perform the installation procedure (see example of projected warning on next page).

GUIDED - Guided should be selected if the user intends to perform a complete alignment of the projected image. All of the necessary geometry and conver- gence adjustments are made in a predetermined sequence.

GENERAL ACCESS

SHARPNESS

TINT

COLOR

BRIGHTNESS

CONTRAST

quit ADJUST

Select with	,
	or
then <ENTER>.

<EXIT> to return

643

ADJUSTMENT MODE

Select a path from below:

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

IRIS

source 1

Select with or then <ENTER> <EXIT> to return

5975977 BARCODATA 708 260597		5-1

Image 25

Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn cleaning On installationOn servicing On repackingRear Panel Terminology Location and Function of ControlsFront Panel Terminology Adjustexit Gaining accessControl panel terminology a. The local keypad RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Switching on/off Power mains cord connectionSignal input connection to the projector ConnectionsSource No Projector input Press digit button Connecting a Composite Video sourceVideo input selection Input selection Connecting a S-Video or Video source to portConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection Connecting a Component source with Tri-level sync Connecting a Component sourceRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selectionConnecting an IR Remote Receiver to the projector Connecting a VS05 switcher to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selectionControlling Battery installation in the RCUHow to display a projector address? How to use the RCUProjector address Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeInternal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePort 2 S-Video/Video Line Doubler optionPeaking Color SelectHorizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeIdentification Projector Set-upData Total Run Time Change passwordChange Language Change Projector Address Power up modeChange baudrate BaudrateMemory management BARCOlogoBarco Logo Memory ManagementDeletion of blocks Copy a blockDeleting block by block Undo all settings to midpos All settings to midpositionALL Settings to Midpos Undo ALL Settings to MidposUndo R & B convergence mid Convergence midGreen convergence mid Undo green convergence midG2 Adjustment Common SettingsCommon Settings G2 AdjustmentProjector warm up CRT Drive ModeProjector Warm UP Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode I2C error Addr FH3 Enter Password Text on Text offFh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just rangeIris commu Nication Error Rcvds com Munication ErrorProjector Will Switch off StartingOptions Line Doubler Kit Magik Interface Orbiting KitCeiling mount CM50 Adapter and communication cablesAdjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Barcodata 708 Insert Card