Barco R9002120 manual Change Projector Address, Change baudrate, Power up mode, Baudrate

Page 42

Service Mode

Change Projector Address

Every projector requires an individual address between O and 255. This address can be software installed.

To change that address, push the control disk up or down to highlight 'Change Porjector Address' and press ENTER. The Change Projec- tor Address menu will be displayed and the actual address will be filled in.

ENTER displays the 'Change Projector Address' menu. EXIT returns to the Service mode main menu.

The first digit is highlighted. Select the individual digits by pushing the control disk to the right or to the left. Reprogram with the digit keys on the RCU.

Press ENTER to confirm.

Press EXIT to return to the projector set up menu.

Change baudrate

The communication speed between projector and computer has 8 possible speeds. The baud rate speed can be software set up. Highlight 'Change Baudrate' by pushing the control disk up or down and press ENTER to display the Baud rate menu.

The following baud rates are available :

-9600

-4800

-2400

-1200

-600

-300

-150

-110

The actual baud rate will be highlighted. To change the baud rate, push the control disk up or down or to the left or to the right to select the desired baud rate and press ENTER to accept this baud rate.

ENTER to accept the selected baud rate.

EXIT to return without changing the baud rate.

Power up mode

When pressing the power switch, the projector can start up in 'operating mode' or in 'stand-by mode'.

Operating mode : the projector start up and displays image .

Stand-by mode : the projector start up in stand-by and waits until the stand-by button or a digit key is pressed.

To change the Power up mode, select Power Up mode by pushing the control disk up or down and press ENTER to toggle between 'Operating' and 'Standby'.

ENTER to toggle between operating and standby.

EXIT to return to the Service menu.

PROJECTOR SET-UP

 

 

IDENTIFICATION

 

 

TOTAL RUN TIME

 

 

CHANGE PASSWORD

 

 

CHANGE LANGUAGE

 

 

CHANGE PROJECTOR ADDRESS

 

CHANGE BAUDRATE

 

 

POWER UP MODE : operating

 

BARCO LOGO

 

 

PROJECTOR ADDRESS

Enter new projector

 

address :

 

0 0 0

 

Use

and

to select,

 

and reprogram

with numeric keys.

Highest address is 255

<ENTER> to confirm

 

<EXIT> to return.

PROJECTOR SET-UP

 

IDENTIFICATION

 

TOTAL RUN TIME

 

CHANGE PASSWORD

 

CHANGE LANGUAGE

 

CHANGE PROJECTOR ADDRESS

 

CHANGE BAUDRATE

 

POWER UP MODE : operating

 

BARCO LOGO

 

BAUDRATE

 

Select new

 

baudrate :

 

9600

4800

2400

1200

600

300

150

110

Select with arrow

 

keys ;

 

<ENTER> to accept

<EXIT> to return.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE : operating

BARCO LOGO

Select with or then <ENTER> <EXIT> to return.

7 - 4

 

5975977 BARCODATA 708 280597

 

Page 41 Page 43
Image 42
Page 41 Page 43
Contents R9002120 Page Barco Projection Systems Date Art. No 260597 R5975977Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Start UP of the Adjustment Mode Options Table of Contents Safety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls Rear Panel TerminologyFront Panel Terminology Control panel terminology a. The local keypad Gaining accessAdjustexit RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Signal input connection to the projector Power mains cord connectionSwitching on/off ConnectionsConnecting a Composite Video source Source No Projector input Press digit buttonVideo input selection Connecting a S-Video or Video source to port Input selectionConnecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selection Connecting a Component sourceConnecting a Component source with Tri-level sync YYB-YS orR-YYsB-Y input selectionRemote control Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector YYB-Y3S or R-YY3sB-Y input selectionBattery installation in the RCU ControllingHow to use the RCU How to display a projector address?Projector address How to program an address into the RCU? Input selection Source No Projector input Press buttonPicture controls Pause keyAdjustment mode Adjustexit StandbyenterPassword WrongStarting up the random access adjustment mode Overview random Access Adjustment modeSelecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Sync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Line Doubler optionPort 2 S-Video/Video Color SelectGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Adjustments BlankingConvergence Adjustment Random Access Adjustment Mode Starting up the Service mode Overview flowchart Service modeProjector Set-up IdentificationData Change password Total Run TimeChange Language Change baudrate Power up modeChange Projector Address BaudrateBarco Logo BARCOlogoMemory management Memory ManagementCopy a block Deletion of blocksDeleting block by block ALL Settings to Midpos All settings to midpositionUndo all settings to midpos Undo ALL Settings to MidposGreen convergence mid Convergence midUndo R & B convergence mid Undo green convergence midCommon Settings Common SettingsG2 Adjustment G2 AdjustmentProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPI2C Diagnostics Permanent Boost Mode USEService Mode Fh= 15.6 kHz Fv= 050 Hz Enter Password Text on Text offI2C error Addr FH3 Invalid Code entry End of ad- just rangeProjector Will Switch off Rcvds com Munication ErrorIris commu Nication Error StartingOptions Ceiling mount CM50 Magik Interface Orbiting KitLine Doubler Kit Adapter and communication cablesAdjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Barcodata 708 Insert Card
Top Page Image Contents