Barco R9002120 Deletion of all blocks, All settings to midposition, Undo all settings to midpos

Page 45

Service Mode

Deletion of all blocks

Highlight 'delete all blocks' with the control disk and press ENTER.

ENTER gives a confirmation message before deleting. EXIT returns to the Path Selection main menu.

If you are certain you wish to delete all blocks, press ENTER to confirm, otherwise press EXIT to return.

Once ENTER is pressed, all block headers and adjustment settings are permanently removed and cannot be restored.

All settings to midposition

Item is password protected.

Highlight 'All settings to midposition' with the control disk and press ENTER to set all settings to their midposition.

A confirmation menu will be displayed first.

ENTER displays a Confirmation screen.

EXIT returns to the Service menu.

ENTER will set all settings to their midposition. EXIT will cancel the operation to set all settings to their midposition.

Undo all settings to midpos

When "All settings to midpos" is selected, all settings are set to their midposition. To cancel this action, select 'Undo all settings to midpos' by pushing the control disk up or down and press ENTER. 'Undo all settings to Midposition' is displayed in the Memory man- agement menu in stead off 'All settings to midposition' when this latter is pressed.

An undo is possible as long as the projector is playing on the same source (= same adjustment block) even when some adjustments as geometry or convergence are already readjusted. When undo is presssed all settings are reset to the previous settings.

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

ALL SETTINGS TO MIDPOS

R & B CONVERGENCE MID

GR CONVERGENCE MID

DELETE ALL BLOCK

All block

will be deleted !

<ENTER> to confirm

<EXIT> to cancel

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

ALL SETTINGS TO MIDPOS

R & B CONVERGENCE MID

GR CONVERGENCE MID

SET TO MIDPOSITION

All settings

on current block

will be overwritten !

<ENTER> to confirm

<EXIT> to cancel

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

UNDO ALL SETTINGS TO MIDPOS

R & B CONVERGENCE MID

GR CONVERGENCE MID

Select with or

then <ENTER>

<EXIT> to return.

5975977 BARCODATA 708 260597		7 - 7

Image 45

Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn cleaning On installationOn servicing On repackingLocation and Function of Controls Rear Panel TerminologyFront Panel Terminology Adjustexit Gaining accessControl panel terminology a. The local keypad RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Switching on/off Power mains cord connectionSignal input connection to the projector ConnectionsConnecting a Composite Video source Source No Projector input Press digit buttonVideo input selection Input selection Connecting a S-Video or Video source to portConnecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection Connecting a Component source with Tri-level sync Connecting a Component sourceRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selectionConnecting an IR Remote Receiver to the projector Connecting a VS05 switcher to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selectionControlling Battery installation in the RCUHow to use the RCU How to display a projector address?Projector address Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeSelecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePort 2 S-Video/Video Line Doubler optionPeaking Color SelectHorizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT E-W TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeProjector Set-up IdentificationData Change password Total Run TimeChange Language Change Projector Address Power up modeChange baudrate BaudrateMemory management BARCOlogoBarco Logo Memory ManagementCopy a block Deletion of blocksDeleting block by block Undo all settings to midpos All settings to midpositionALL Settings to Midpos Undo ALL Settings to MidposUndo R & B convergence mid Convergence midGreen convergence mid Undo green convergence midG2 Adjustment Common SettingsCommon Settings G2 AdjustmentProjector warm up CRT Drive ModeProjector Warm UP Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode I2C error Addr FH3 Enter Password Text on Text offFh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just rangeIris commu Nication Error Rcvds com Munication ErrorProjector Will Switch off StartingOptions Line Doubler Kit Magik Interface Orbiting KitCeiling mount CM50 Adapter and communication cablesAdjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Barcodata 708 Insert Card