Barco R9002120 manual Line Doubler option, Port 2 S-Video/Video, Peaking, Color Select

Page 30

Random Access Adjustment Mode

Line Doubler (option)

Line doubling is only possible for Video, S-Video, Component Video images on standard line frequency and RGB signals on 15 kHz.

To eliminate the video line patterns and to improve the image stability, the line doubler has to be switched on. The line doubler is default set in the ON position when starting up for the first time. The setting of the line doubler will be saved together with the source number. Each time this source number is selected, the last saved version will be loaded.

Highlight Line Doubler with the control disk and press ENTER to toggle between ON (active) and OFF (non active).

EXIT will return to the random access selection menu.

Port 2 : S-Video/Video

Port 2 can be used as Video or S-Video input.

Highlight Port 2 by pushing the control disk up or down and press ENTER to toggle between Video and S-Video.

Peaking

Peaking improves the contours in an projected image.

Highlight PEAKING by pushing the control disk up or down and press ENTER to toggle the peaking between OFF and ON.

During the creation of new settings for a RGB source the peaking is switched to OFF.

Color Select

Highlight COLOR SELECT by pushing the control disk up or down and press ENTER to display the color select menu.

ENTER continues to the color select menu.

EXIT will return to Internal Crosshatch Selection or Setup Pattern Selection Menu.

ADJUST returns to operational mode.

Use the control disk to highlight a color (CRT) or combination of colors to display the projected image in that specific color.

To select a new color, press ENTER, the color selection menu appears again on the screen. To terminate the color select proce- dure, press EXIT.

ENTER continues with the selected color or color combina- tion.

EXIT returns to the Random access main menu.

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PEAKING : ON

Select with

or

<ENTER> to accept

<EXIT> to return.

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PEAKING :ON

LINE DOUBLER : ON

PORT 2 : S-VIDEO

Select with

or

<ENTER> to accept

<EXIT> to return.

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PEAKING : OFF

LINE DOUBLER : ON

Select with

or

<ENTER> to accept

<EXIT> to return.

RANDOM ACCESS

 

ADJUSTMENT MODE

 

PICTURE TUNING

 

GEOMETRY

 

CONVERGENCE

 

COLOR SELECT

 

COLOR SELECT

RED

 

GREEN

 

BLUE

 

RED AND GREEN

BLUE AND GREEN

RED AND BLUE

Select with

or

<ENTER> to accept

<EXIT> to return.

6-4

 

5975977 BARCODATA 708 260597

 

Image 30
Contents R9002120 Page Barco Projection Systems Date Art. No 260597 R5975977Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Start UP of the Adjustment Mode Options Table of Contents Safety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls Rear Panel TerminologyFront Panel Terminology Control panel terminology a. The local keypad Gaining accessAdjustexit RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Signal input connection to the projector Power mains cord connectionSwitching on/off ConnectionsConnecting a Composite Video source Source No Projector input Press digit buttonVideo input selection Connecting a S-Video or Video source to port Input selectionConnecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selection Connecting a Component sourceConnecting a Component source with Tri-level sync YYB-YS orR-YYsB-Y input selectionRemote control Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector YYB-Y3S or R-YY3sB-Y input selectionBattery installation in the RCU ControllingHow to use the RCU How to display a projector address?Projector address How to program an address into the RCU? Input selection Source No Projector input Press buttonPicture controls Pause keyAdjustment mode Adjustexit StandbyenterPassword WrongStarting up the random access adjustment mode Overview random Access Adjustment modeSelecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Sync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Line Doubler optionPort 2 S-Video/Video Color SelectGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Adjustments BlankingConvergence Adjustment Random Access Adjustment Mode Starting up the Service mode Overview flowchart Service modeProjector Set-up IdentificationData Change password Total Run TimeChange Language Change baudrate Power up modeChange Projector Address BaudrateBarco Logo BARCOlogoMemory management Memory ManagementCopy a block Deletion of blocksDeleting block by block ALL Settings to Midpos All settings to midpositionUndo all settings to midpos Undo ALL Settings to MidposGreen convergence mid Convergence midUndo R & B convergence mid Undo green convergence midCommon Settings Common SettingsG2 Adjustment G2 AdjustmentProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPI2C Diagnostics Permanent Boost Mode USEService Mode Fh= 15.6 kHz Fv= 050 Hz Enter Password Text on Text offI2C error Addr FH3 Invalid Code entry End of ad- just rangeProjector Will Switch off Rcvds com Munication ErrorIris commu Nication Error StartingOptions Ceiling mount CM50 Magik Interface Orbiting KitLine Doubler Kit Adapter and communication cablesAdjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Barcodata 708 Insert Card