Barco R9002120 manual BARCOlogo, Memory management, Barco Logo, Memory Management

Page 43

Service Mode

BARCO_logo

The BARCO logo can be added to the image, in overlay or in background, on any place on the screen.

To add the BARCO logo or to change a setting in the BARCO logo menu, highlight 'BARCO logo' by pushing the control disk up or down and press ENTER to select.

WARNING : Continuous use of the BARCO logo damages the

RED CRT.

ENTER displays the BARCO logo menu.

EXIT returns to the Service menu

The BARCO logo menu will be displayed on the screen. Within this menu, four toggle settings are available.

Mode [ON/OFF] :

ON : BARCO logo will be displayed on the screen.

To position the logo on the screen, push the control disk up, down, to the left or to the right until the desired position is reached.

OFF : No BARCO logo displayed on the screen.

Size [SMALL/LARGE] :

SMALL : Small BARCO logo will be displayed if mode is on.

LARGE : Large (double size) BARCO logo will be displayed if mode is on.

Background [ON/OFF] :

ON : BARCO logo will be displayed on a black background.

BARCO

OFF : BARCO logo will be displayed without any background.

BARCO

Orbiting [ON/OFF] :

ON : on the BARCO logo will orbit around it axis.

OFF : no orbit of the BARCO logo.

Memory management

Highlight 'Memory management' by pushing the control disk up or down and press ENTER to display the memory management menu. Within the memory management menu, the following items can be consultated or executed :

-copy a block

-delete a block

-delete all blocks

-all settings to midposition

-R & B convergence to mid

-Gr convergence mid (only if green convergence is available)

PROJECTOR SET-UP

IDENTIFICATION

TOTALRUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE : operating

BARCO LOGO

BARCO LOGO

MODE : ON

SIZE : SMALL

BACKGROUND : ON

ORBITTING : ON

You can move the logo

on the screen, using

the arrow keys.

WARNING : continuous use of the BARCO logo damages the RED CRT !

Select with or <ENTER> to toggle

<EXIT> to return.

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

ALL SETTINGS TO MIDPOS

R & B CONVERGENCE MID

GR CONVERGENCE MID

Select with or then <ENTER> <EXIT> to return.

5975977 BARCODATA 708 260597		7 - 5

Image 43

Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn repacking On installationOn cleaning On servicingRear Panel Terminology Location and Function of ControlsFront Panel Terminology RCU control panel terminology Gaining accessAdjustexit Control panel terminology a. The local keypadLocation and Function of Controls Location and Function of Controls Connections Power mains cord connectionSwitching on/off Signal input connection to the projectorSource No Projector input Press digit button Connecting a Composite Video sourceVideo input selection Input selection Connecting a S-Video or Video source to portConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection YYB-YS orR-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RGB3S or RG3sB input selectionYYB-Y3S or R-YY3sB-Y input selection Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Remote controlControlling Battery installation in the RCUHow to display a projector address? How to use the RCUProjector address Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeInternal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select Line Doubler optionPort 2 S-Video/Video PeakingGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Raster Shift AdjustmentProjected raster Crt faceplate borderLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeIdentification Projector Set-upData Total Run Time Change passwordChange Language Baudrate Power up modeChange Projector Address Change baudrateMemory Management BARCOlogoMemory management Barco LogoDeletion of blocks Copy a blockDeleting block by block Undo ALL Settings to Midpos All settings to midpositionUndo all settings to midpos ALL Settings to MidposUndo green convergence mid Convergence midUndo R & B convergence mid Green convergence midG2 Adjustment Common SettingsG2 Adjustment Common SettingsProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode Invalid Code entry End of ad- just range Enter Password Text on Text offI2C error Addr FH3 Fh= 15.6 kHz Fv= 050 HzStarting Rcvds com Munication ErrorIris commu Nication Error Projector Will Switch offOptions Adapter and communication cables Magik Interface Orbiting KitLine Doubler Kit Ceiling mount CM50Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Barcodata 708 Insert Card