Barco R9002120 manual Random access adjustment mode selection menu, Picture Tuning, Color Balance

Page 29

Random Access Adjustment Mode

Random access adjustment mode selection menu.

This is the main menu for the Random Access adjustment mode.

Through this menu, the following adjustments and features are accessible :

- Picture Tuning

Enhanced Blue (only for RGB)

Sync slow/fast(video/s-video)

Color Balance

-Geometry

-Convergence

-Color select

And also Orbiting, Contrast modulation and Soft Edge if these options are installed.

Picture Tuning

Highlight Picture tuning by pushing the control disk up or down and press ENTER. The Picture tuning menu will be displayed.

Depending on the input source, the 'Picture tuning' menu will display different items.

-Color Balance

-Sync slow/fast

-Line doubler

-Port 2 : S-Video

-Peaking

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

 

CONVERGENCE

COLOR SELECT

Select with

or

then <ENTER>

<EXIT> to return.

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PORT 2 : S-VIDEO

PEAKING : ON

LINE DOUBLER : ON

Select with

or

<ENTER> to accept

<EXIT> to return.

Color Balance

The Color Balance function is used to select or adjust the color temperature of white used by the projector.

The Color Balance can be adjusted on two different ways :

-fixed color balance. You have the choice between 3200 K (reddish), 4900 K, 6500 K (white) or 9300 K (bluish).

-Custom white and black balance.

Fixed Color Balance.

Highlight one of the 4 preprogrammed color temperatures with the control disk and press ENTER to display the desired color balance.

Custom Color Balance.

Select custom white balance by pushing the control disk up or down and press ENTER to start the adjustment.

Push the control disk up or down to adjust the red gain and push the control disk to the left or to the right to adjust the blue gain. A bar scale indicates the amount of adjustment.

Select custom black balance with the control disk and press ENTER to start the adjustment.

Push the control disk up or down to adjust the red cut-off and push the control disk to the left or to the right to adjust the blue cut-off. When the color balance is adjusted, select continue by pushing the control disk up or down and press ENTER.

Sync Fast/Slow Adjustment

The sync function is used to minimize horizontal jittering or tearing at the top to the displayed image.

Highlight SYNC with the control disk and press ENTER to toggle between FAST and SLOW.

Note: SYNC is normally used in the SLOW position. The FAST position is used to compensate for unsteady sync pulses from older video playback equipment.

Hint : when the line doubler feature is ON (active), toggle the sync to FAST.

ENTER will toggle Sync between FAST and SLOW

EXIT will return to the Randam Access Adjustment menu.

PICTURE TUNING

 

COLOR BALANCE

 

SYNC : FAST

 

PEAKING : ON

 

LINE DOUBLER : ON

 

COLOR BALANCE

FIXED COLOR BALANCE

3200 4900 6500 9300

CUSTOM WHITE BALANCE

CUSTOM BLACK BALANCE

Select with arrow keys

then <ENTER>

You can

 

adjust red with

or

Blue with

or

<EXIT> to return

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

LINE DOUBLER : ON

Select with

or

<ENTER> to accept

<EXIT> to return.

5975977 BARCODATA 708 260597

 

6-3

 

Image 29
Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn cleaning On installationOn servicing On repackingFront Panel Terminology Location and Function of ControlsRear Panel Terminology Adjustexit Gaining accessControl panel terminology a. The local keypad RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Switching on/off Power mains cord connectionSignal input connection to the projector ConnectionsVideo input selection Connecting a Composite Video sourceSource No Projector input Press digit button Input selection Connecting a S-Video or Video source to portRgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync Connecting a Component source with Tri-level sync Connecting a Component sourceRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selectionConnecting an IR Remote Receiver to the projector Connecting a VS05 switcher to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selectionControlling Battery installation in the RCUProjector address How to use the RCUHow to display a projector address? Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeInternal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Picture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePort 2 S-Video/Video Line Doubler optionPeaking Color SelectHorizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeData Projector Set-upIdentification Change Language Change passwordTotal Run Time Change Projector Address Power up modeChange baudrate BaudrateMemory management BARCOlogoBarco Logo Memory ManagementDeleting block by block Copy a blockDeletion of blocks Undo all settings to midpos All settings to midpositionALL Settings to Midpos Undo ALL Settings to MidposUndo R & B convergence mid Convergence midGreen convergence mid Undo green convergence midG2 Adjustment Common SettingsCommon Settings G2 AdjustmentProjector warm up CRT Drive ModeProjector Warm UP Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode I2C error Addr FH3 Enter Password Text on Text offFh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just rangeIris commu Nication Error Rcvds com Munication ErrorProjector Will Switch off StartingOptions Line Doubler Kit Magik Interface Orbiting KitCeiling mount CM50 Adapter and communication cablesSource numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Barcodata 708 Insert Card