Barco R9002120 manual Left-Right east-west Adjustments, Left-Right E-W

Page 33

Random Access Adjustment Mode

Left-Right (east-west) Adjustments

Left-right and center adjustments affect only the vertical lines of the projected image.

To start up the left-right and center adjustments, follow the next procedure :

Push the control disk up or down to highlight LEFT-RIGHT (E/W) on the geometry menu and then press ENTER.

ENTER will select Left-Right adjustment menu

EXIT returns to random access adjustment mode main menu. ADJUST returns to operational mode

Only the green image is displayed while making left-right adjust- ments. The red and blue images will automatically be corrected in the same manner. Convergence corrections are automatically disabled for the duration of these adjustments.

The following adjustments can be executed

-vertical centerline bow

-vertical centerline skew

-side keystone (left - right)

-side bow (left - right)

All adjustment are indicated on the screen with the function name, a bar scale and a number between 0 and 100.

Adjust the next alignments until the vertical lines are straight.

To enter an alignment, push the control disk up or down to highlight a function and press ENTER to activate this function.

Press EXIT to return.

LEFT-RIGHT (E-W)

V CENTERLINE BOW

V CENTERLINE SKEW

RIGHT BOW

RIGHT KEYSTONE

LEFT BOW

LEFT KEYSTONE

Select with or then <ENTER> <EXIT> to return.

5975977 BARCODATA 708 260597

GEOMETRY

 

H PHASE

 

RASTER SHIFT

 

LEFT-RIGHT (E-W)

 

TOP-BOTTOM (N-S)

 

SIZE

 

V LINEARITY

 

BLANKING

 

LEFT-RIGHT (E-W)

V CENTERLINE BOW

V CENTERLINE SKEW

RIGHT BOW

RIGHT KEYSTONE

LEFT BOW

 

LEFT KEYSTONE

Select with

or

then <ENTER>

<EXIT> to return.

Corrects for curvature of the vertical lines in the middle of the image.

Corrects the tilting of the vertical lines in the middle of the image.

Corrects for curvature of the vertical lines on the right side

Corrects the keystone geometry correction of the vert. lines on the right side

Corrects for curvature of the vertical lines on the left side

Corrects the keystone geometry correction of the vert. lines on the left side

Correct by pushing

Correct by pushing

the control disk to the

the control disk to

right

the left

 

6-7

Image 33
Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn cleaning On installationOn servicing On repackingLocation and Function of Controls Rear Panel TerminologyFront Panel Terminology Adjustexit Gaining accessControl panel terminology a. The local keypad RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Switching on/off Power mains cord connectionSignal input connection to the projector ConnectionsConnecting a Composite Video source Source No Projector input Press digit buttonVideo input selection Input selection Connecting a S-Video or Video source to portConnecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection Connecting a Component source with Tri-level sync Connecting a Component sourceRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selectionConnecting an IR Remote Receiver to the projector Connecting a VS05 switcher to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selectionControlling Battery installation in the RCUHow to use the RCU How to display a projector address?Projector address Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeSelecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePort 2 S-Video/Video Line Doubler optionPeaking Color SelectHorizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT E-W TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeProjector Set-up IdentificationData Change password Total Run TimeChange Language Change Projector Address Power up modeChange baudrate BaudrateMemory management BARCOlogoBarco Logo Memory ManagementCopy a block Deletion of blocksDeleting block by block Undo all settings to midpos All settings to midpositionALL Settings to Midpos Undo ALL Settings to MidposUndo R & B convergence mid Convergence midGreen convergence mid Undo green convergence midG2 Adjustment Common SettingsCommon Settings G2 AdjustmentProjector warm up CRT Drive ModeProjector Warm UP Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode I2C error Addr FH3 Enter Password Text on Text offFh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just rangeIris commu Nication Error Rcvds com Munication ErrorProjector Will Switch off StartingOptions Line Doubler Kit Magik Interface Orbiting KitCeiling mount CM50 Adapter and communication cablesAdjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Barcodata 708 Insert Card