Barco R9002120 manual Convergence Adjustment, Adjustment Mode

Page 37

Random Access Adjustment Mode

Convergence Adjustment

Convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on the red image while superimposed on the green image and then on the blue image while superimposed on the green image.

Note : the green convergence adjustments can be added as an option. When these are available, start always with 'green only'. This option will also be indicated on the convergence menu.

Highlight first 'Green only' when available by pushing the control disk up or down and press ENTER to display the convergence adjustment menu.

The screen area is divided into 25 areas.

Use the control disk to move the box to the desired zone and then press ENTER to begin the convergence adjustment. Start the convergence adjustment with zone one and continue as mentioned in the diagram hereafter.

Use the control disk to make horizontal or vertical convergence adjustments in the selected zone and then press ENTER to move the box to another zone or EXIT to return to the Convergence menu.

ENTER toggles the control disk between zone selection and zone adjustment .

EXIT returns to convergence menu

	RANDOM ACCESS
	ADJUSTMENT MODE
	PICTURE TUNING
	GEOMETRY
	CONVERGENCE
	COLOR SELECT
		CONVERGENCE
		GREEN ONLY
		RED ON GREEN
		BLUE ON GREEN
		Select with	or
		then <ENTER>
		<EXIT> to return.
25	23	9	15	17
24	22	8	14	16
5	4	1	2	3
20	18	6	10	12
21	19	7	11	13
		CONVERGENCE

SEL : select area using arrow keys

ADJ : adjust area using arrow keys

Toggle between SEL and ADJ with <ENTER> <ENTER> continue <EXIT> to return

CONVERGE

ADJUSTMENT

green image	70

red image

5975977 BARCODATA 708 260597		6-11

Image 37

Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn cleaning On installationOn servicing On repackingRear Panel Terminology Location and Function of ControlsFront Panel Terminology Adjustexit Gaining accessControl panel terminology a. The local keypad RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Switching on/off Power mains cord connectionSignal input connection to the projector ConnectionsSource No Projector input Press digit button Connecting a Composite Video sourceVideo input selection Input selection Connecting a S-Video or Video source to portConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection Connecting a Component source with Tri-level sync Connecting a Component sourceRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selectionConnecting an IR Remote Receiver to the projector Connecting a VS05 switcher to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selectionControlling Battery installation in the RCUHow to display a projector address? How to use the RCUProjector address Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeInternal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePort 2 S-Video/Video Line Doubler optionPeaking Color SelectHorizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeIdentification Projector Set-upData Total Run Time Change passwordChange Language Change Projector Address Power up modeChange baudrate BaudrateMemory management BARCOlogoBarco Logo Memory ManagementDeletion of blocks Copy a blockDeleting block by block Undo all settings to midpos All settings to midpositionALL Settings to Midpos Undo ALL Settings to MidposUndo R & B convergence mid Convergence midGreen convergence mid Undo green convergence midG2 Adjustment Common SettingsCommon Settings G2 AdjustmentProjector warm up CRT Drive ModeProjector Warm UP Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode I2C error Addr FH3 Enter Password Text on Text offFh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just rangeIris commu Nication Error Rcvds com Munication ErrorProjector Will Switch off StartingOptions Line Doubler Kit Magik Interface Orbiting KitCeiling mount CM50 Adapter and communication cablesAdjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Barcodata 708 Insert Card