Barco R9002120 Connecting a RGB Analog source with composite sync, Rgbs or RGsB input selection

Page 18

Connections

Connecting a RGB Analog source with composite sync.

RGB analog input terminals with composite sync input or with sync on green. The projector detects automatically where the sync signal is located.

Always use an interface when a computer and local monitor have to be connected to the projector. Examples of interfaces which can be applied :

Universal analog interface	R9826100
RGB 120 MHz Analog Interface	R9826570	(230V)
Multifunctional Analog Interface Kit	R9828120	(230V)
(MAGIK)	R9828129	(120V)
VGA interface	R9828070	(230V)
	R9828079	(120V)
MAC interface	R9828050	(230V)
	R9828059	(120V)

RGBS or RGsB input selection

a. Press digit button 3 on the RCU or

b. With the local keypad :

(to gain access to the local keypad, see 'Local keypad' in chapter 'Location and function of controls'.)

-Press ADJUST key, the General access menu is displayed on the screen.

-Use the control disk to highlight 3.

-Press ENTER to select the highlighted source.

RS232 OUT

COMM PORT

R

G( S)

B

S-VIDEO

RS232 IN

(800 peripherals) REMOTE

R-Y

Y(S)

B-Y

S VIDEO

ANALOG OUT

R G B S

INP UT

	GENERAL ACCESS
		SHARPNESS
		TINT
5	6	COLOR
3	4	BRIGHTNESS
1	2	CONTRAST

Enter ADJUST

Select with	,
	or
then <ENTER>.

<EXIT> to return

Connecting a RGB Analog source with Tri-level sync.

RGB analog input terminals with Tri level sync input or with Tri- level sync on green. The projector detects automatically where the sync signal is located.

COMM PORT

REMOTE

R

G( S)

B

S-VIDEO

RS232 IN

RS232 OUT

(800 peripherals)

S VIDEO

R-Y

Y(S)

B-Y

VCR HDTV player

Audio amplifier

3 - 4		5975977 BARCODATA 708 260597

Image 18

Contents R9002120 Page Barco Projection Systems Date Art. No 260597 R5975977Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Start UP of the Adjustment Mode Options Table of Contents Safety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls Rear Panel TerminologyFront Panel Terminology Control panel terminology a. The local keypad Gaining accessAdjustexit RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Signal input connection to the projector Power mains cord connectionSwitching on/off ConnectionsConnecting a Composite Video source Source No Projector input Press digit buttonVideo input selection Connecting a S-Video or Video source to port Input selectionConnecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selection Connecting a Component sourceConnecting a Component source with Tri-level sync YYB-YS orR-YYsB-Y input selectionRemote control Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector YYB-Y3S or R-YY3sB-Y input selectionBattery installation in the RCU ControllingHow to use the RCU How to display a projector address?Projector address How to program an address into the RCU? Input selection Source No Projector input Press buttonPicture controls Pause keyAdjustment mode Adjustexit StandbyenterPassword WrongStarting up the random access adjustment mode Overview random Access Adjustment modeSelecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Sync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Line Doubler optionPort 2 S-Video/Video Color SelectGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Adjustments BlankingConvergence Adjustment Random Access Adjustment Mode Starting up the Service mode Overview flowchart Service modeProjector Set-up IdentificationData Change password Total Run TimeChange Language Change baudrate Power up modeChange Projector Address BaudrateBarco Logo BARCOlogoMemory management Memory ManagementCopy a block Deletion of blocksDeleting block by block ALL Settings to Midpos All settings to midpositionUndo all settings to midpos Undo ALL Settings to MidposGreen convergence mid Convergence midUndo R & B convergence mid Undo green convergence midCommon Settings Common SettingsG2 Adjustment G2 AdjustmentProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPI2C Diagnostics Permanent Boost Mode USEService Mode Fh= 15.6 kHz Fv= 050 Hz Enter Password Text on Text offI2C error Addr FH3 Invalid Code entry End of ad- just rangeProjector Will Switch off Rcvds com Munication ErrorIris commu Nication Error StartingOptions Ceiling mount CM50 Magik Interface Orbiting KitLine Doubler Kit Adapter and communication cablesAdjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Barcodata 708 Insert Card