Barco R9002120 manual Size Adjustment, Vertical Linearity Adjustment

Page 35

Random Access Adjustment Mode

Size Adjustment

Push the control disk up or down to highlight SIZE on the Geometry menu and then press ENTER.

ENTER will select size adjustment.

EXIT returns to random access adjustment mode menu. ADJUST returns to operational mode.

Adjust the horizontal size by pushing the control disk to the right or to the left until the exact image width is obtained.

Adjust the vertical size by pushing the control disk up or down until the exact image height is obtained.

Note :

-If the internal # pattern was selected, this pattern remains on the screen.

-If the genlocked pattern was selected, the external source will be displayed.

A bar scale and a numeric indicator help to gauge the size adjustment.

Hint : In order to avoid loss of resolution in the projected image and to ensure maximum CRT longevity, do not use an excessively small horizontal size setting.

EXIT will return to Geometry.

Ideal

 

Ideal

 

Image too

 

 

Image

Image

Image too

Hight

Tall

Hight

Short

 

 

 

 

 

 

 

 

 

 

 

 

Vertical Linearity Adjustment

The vertical linearity adjustment function corrects for vertical non- linearities which extend from the center of the image to the top and bottom of the image.

Push the control disk up or down to highlight V LINEARITY on the Geometry menu and then press ENTER.

ENTER will select vertical linearity adjustment.

EXIT returns to random access adjustment mode menu. ADJUST returns to operational mode.

Adjust the vertical linearity with the control disk until the distances between the horizontal lines of the set up pattern are equal from top to bottom.

EXIT will return to the Geometry menu.

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

TOP-BOTTOM (N-S)

SIZE

V LINEARITY

BLANKING

H SIZE

70

H size too large

Ideal image width

H size too small

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

VSIZE

BLANKING

V LINEARITY

70

5975977 BARCODATA 708 260597

 

6-9

 

Image 35
Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn repacking On installationOn cleaning On servicingFront Panel Terminology Location and Function of ControlsRear Panel Terminology RCU control panel terminology Gaining accessAdjustexit Control panel terminology a. The local keypadLocation and Function of Controls Location and Function of Controls Connections Power mains cord connectionSwitching on/off Signal input connection to the projectorVideo input selection Connecting a Composite Video sourceSource No Projector input Press digit button Input selection Connecting a S-Video or Video source to portRgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync YYB-YS orR-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RGB3S or RG3sB input selectionYYB-Y3S or R-YY3sB-Y input selection Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Remote controlControlling Battery installation in the RCUProjector address How to use the RCUHow to display a projector address? Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeInternal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select Line Doubler optionPort 2 S-Video/Video PeakingGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Raster Shift AdjustmentProjected raster Crt faceplate borderLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeData Projector Set-upIdentification Change Language Change passwordTotal Run Time Baudrate Power up modeChange Projector Address Change baudrateMemory Management BARCOlogoMemory management Barco LogoDeleting block by block Copy a blockDeletion of blocks Undo ALL Settings to Midpos All settings to midpositionUndo all settings to midpos ALL Settings to MidposUndo green convergence mid Convergence midUndo R & B convergence mid Green convergence midG2 Adjustment Common SettingsG2 Adjustment Common SettingsProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode Invalid Code entry End of ad- just range Enter Password Text on Text offI2C error Addr FH3 Fh= 15.6 kHz Fv= 050 HzStarting Rcvds com Munication ErrorIris commu Nication Error Projector Will Switch offOptions Adapter and communication cables Magik Interface Orbiting KitLine Doubler Kit Ceiling mount CM50Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Barcodata 708 Insert Card