Barco R9002120 manual Top-Bottom north-south Adjustments, Top-Bottom N-S

Page 34

Random Access Adjustment Mode

Top-Bottom (north-south) Adjustments

Top-Bottom and center adjustments affect only the horizontal lines of the projected image.

To start up the Top-Bottom and center corrections, follow the next procedure :

Push the control disk up or down to highlight TOP-BOTTOM (N/S) on the geometry menu and then press ENTER.

Only the green image is displayed while making top-botton adjust- ments. The red and blue images will automatically be corrected in the same manner. Convergence corrections are automatically disabled for the duration of these adjustments.

The following adjustments can be executed :

-Horizontal centerline bow

-Horizontal centerline skew

-Top bow

-Top keystone

-Bottom bow

-Bottom keystone

All adjustment are indicated on the screen with the function name, a bar scale and a number between 0 and 100.

Adjust the next alignments until the vertical lines are straight.

To enter an alignment, push the control disk up or down to highlight a function and press ENTER to activate this function.

Press EXIT to return.

TOP-BOTTOM

H CENTERLINE BOW

H CENTERLINE SKEW

TOP BOW

TOP KEYSTONE

BOTTOM BOW

BOTTOM KEYSTONE

Select with or

then <ENTER> <EXIT> to return.

GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
TOP-BOTTOM (N-S)
SIZE
V LINEARITY
BLANKING
TOP-BOTTOM (N-S)
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP BOW
BOTTOM KEYSTONE
BOTTOM BOW
Select with	or
then <ENTER>
<EXIT> to return.

Corrects for curvature of the horizontal lines in the middle of the image.

Corrects the tilting of the horizontal lines in the middle of the image.

Corrects for curvature of the horizontal lines on the upper side

Corrects the keystone geometry correction of the hor. lines on the upper side

Corrects for curvature of the horizontal lines on the lower side

Corrects the keystone geometry correction of the hor. lines on the lower side


	Correct by pushing		Correct by pushing
	the control stick		the control stick
	backward		forward
6-8		5975977 BARCODATA 708 260597
6-8		5975977 BARCODATA 708 260597

Image 34

Contents R9002120 Page Barco Projection Systems Date Art. No 260597 R5975977Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Start UP of the Adjustment Mode Options Table of Contents Safety Instructions On safetyOn servicing On installationOn cleaning On repackingRear Panel Terminology Location and Function of ControlsFront Panel Terminology Control panel terminology a. The local keypad Gaining accessAdjustexit RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Signal input connection to the projector Power mains cord connectionSwitching on/off ConnectionsSource No Projector input Press digit button Connecting a Composite Video sourceVideo input selection Connecting a S-Video or Video source to port Input selectionConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection RGB3S or RG3sB input selection Connecting a Component sourceConnecting a Component source with Tri-level sync YYB-YS orR-YYsB-Y input selectionRemote control Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector YYB-Y3S or R-YY3sB-Y input selectionBattery installation in the RCU ControllingHow to display a projector address? How to use the RCUProjector address How to program an address into the RCU? Input selection Source No Projector input Press buttonPicture controls Pause keyAdjustment mode Adjustexit StandbyenterPassword WrongStarting up the random access adjustment mode Overview random Access Adjustment modeInternal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Sync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Line Doubler optionPort 2 S-Video/Video Color SelectGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments BlankingConvergence Adjustment Random Access Adjustment Mode Starting up the Service mode Overview flowchart Service modeIdentification Projector Set-upData Total Run Time Change passwordChange Language Change baudrate Power up modeChange Projector Address BaudrateBarco Logo BARCOlogoMemory management Memory ManagementDeletion of blocks Copy a blockDeleting block by block ALL Settings to Midpos All settings to midpositionUndo all settings to midpos Undo ALL Settings to MidposGreen convergence mid Convergence midUndo R & B convergence mid Undo green convergence midCommon Settings Common SettingsG2 Adjustment G2 AdjustmentProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPI2C Diagnostics Permanent Boost Mode USEService Mode Fh= 15.6 kHz Fv= 050 Hz Enter Password Text on Text offI2C error Addr FH3 Invalid Code entry End of ad- just rangeProjector Will Switch off Rcvds com Munication ErrorIris commu Nication Error StartingOptions Ceiling mount CM50 Magik Interface Orbiting KitLine Doubler Kit Adapter and communication cablesAdjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Barcodata 708 Insert Card