Barco R9002120 manual Controlling, Battery installation in the RCU

Page 21

Controlling

4 CONTROLLING

Caution : Do not display a stationary image with full brightness and contrast for longer than 20 min., otherwise you risk damage to the CRT's.

Battery installation in the RCU.

A new battery is delivered inside the plastic bag with the power cord. Before using the RCU, install first the battery.

Remove the battery cover on the backside of the remote control by pushing the indicated handle a little to the bottom of the RCU. Lift up the top side of the cover at the same time (fig. 1).

Insert the new 9 V battery (E-block type, e.g. 6F22S or equivalent) in the lower compartment and connect the battery to the contact plate.

Insert the battery into the lower compartment and put the cover back.

 

Insert here,

 

 

behind the

 

 

plastic cover, the

fig.1

 

'Insert card for

 

 

 

RCU'. You can

 

Contact

cut out this card

 

plate

on one of the

 

 

last pages of this

 

 

manual.

 

Battery

fig.2

310a.DRW

5975977 BARCODATA 708 260597

 

4-1

 

Image 21
Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn cleaning On installationOn servicing On repackingLocation and Function of Controls Rear Panel TerminologyFront Panel Terminology Adjustexit Gaining accessControl panel terminology a. The local keypad RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Switching on/off Power mains cord connectionSignal input connection to the projector ConnectionsConnecting a Composite Video source Source No Projector input Press digit buttonVideo input selection Input selection Connecting a S-Video or Video source to portConnecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection Connecting a Component source with Tri-level sync Connecting a Component sourceRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selectionConnecting an IR Remote Receiver to the projector Connecting a VS05 switcher to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selectionControlling Battery installation in the RCUHow to use the RCU How to display a projector address?Projector address Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeSelecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePort 2 S-Video/Video Line Doubler optionPeaking Color SelectHorizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT E-W TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeProjector Set-up IdentificationData Change password Total Run TimeChange Language Change Projector Address Power up modeChange baudrate BaudrateMemory management BARCOlogoBarco Logo Memory ManagementCopy a block Deletion of blocksDeleting block by block Undo all settings to midpos All settings to midpositionALL Settings to Midpos Undo ALL Settings to MidposUndo R & B convergence mid Convergence midGreen convergence mid Undo green convergence midG2 Adjustment Common SettingsCommon Settings G2 AdjustmentProjector warm up CRT Drive ModeProjector Warm UP Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode I2C error Addr FH3 Enter Password Text on Text offFh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just rangeIris commu Nication Error Rcvds com Munication ErrorProjector Will Switch off StartingOptions Line Doubler Kit Magik Interface Orbiting KitCeiling mount CM50 Adapter and communication cablesAdjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Barcodata 708 Insert Card