Barco R9002120 manual Connecting a S-Video or Video source to port, Input selection

Page 17

Connections

Connecting a S-Video or Video source to port 2.

Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals.

If a line doubler is built in :

the default position of this line doubler is ON (active), the video input signal will be displayed as a non interlaced image (= improved image stability).

To enable or to disable this line doubler function, enter the adjustment mode and change the position of the ON/OFF toggle switch (see Picture tuning in chapter 'Guided' adjust- ment mode or 'Random access' adjustment mode).

Input selection

a. with the RCU : press digit button 2 or

b. with the local keypad.

(for access to the local keypad, see Local keypad in chapter Location and function of controls.)

-press ADJUST key, the General access menu is displayed on the screen.

-use the control disk to highlight 2.

-press ENTER to select the highlighted source.

Depending on the priority setting in the 'Picture Tuning menu', Video or S-Video can be displayed.

If the setting is not correct, start up the adjustment mode by pushing on the ADJUST key.

Select 'Random Access' and press ENTER.

Select 'Selected source' and press ENTER.

Highlight 'Picture Tuning' and press ENTER.

Highlight 'Port 2 : Video' and press ENTER to toggle between VIDEO and S-VIDEO.

Press EXIT to return.

Press ADJUST to return to operational mode.

RS232 IN

RS232 OUT

COMM PORT

R

G(S)

B

S VIDEO

S-VIDEO

(800 peripherals) REMOTE

R-Y

Y(S)

B-Y

Luma/Chroma

VCR S-VHS

Audio amplifier

	GENERAL ACCESS
		SHARPNESS
		TINT
5	6	COLOR
3	4	BRIGHTNESS
1	2	CONTRAST

Enter ADJUST

Select with	,
	or
then <ENTER>.

<EXIT> to return

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS

INSTALLATION

Choose a setup pattern from below :

SELECTED SOURCE

GENLOCKED PATTERN

INTERNAL # PATTERN

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PORT2 : S-VIDEO

LINE DOUBLER : ON

Select with or <ENTER> to accept

<EXIT> to return.

5975977 BARCODATA 708 260597		3 - 3

Image 17

Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn cleaning On installationOn servicing On repackingFront Panel Terminology Location and Function of ControlsRear Panel Terminology Adjustexit Gaining accessControl panel terminology a. The local keypad RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Switching on/off Power mains cord connectionSignal input connection to the projector ConnectionsVideo input selection Connecting a Composite Video sourceSource No Projector input Press digit button Input selection Connecting a S-Video or Video source to portRgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync Connecting a Component source with Tri-level sync Connecting a Component sourceRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selectionConnecting an IR Remote Receiver to the projector Connecting a VS05 switcher to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selectionControlling Battery installation in the RCUProjector address How to use the RCUHow to display a projector address? Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeInternal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Picture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePort 2 S-Video/Video Line Doubler optionPeaking Color SelectHorizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeData Projector Set-upIdentification Change Language Change passwordTotal Run Time Change Projector Address Power up modeChange baudrate BaudrateMemory management BARCOlogoBarco Logo Memory ManagementDeleting block by block Copy a blockDeletion of blocks Undo all settings to midpos All settings to midpositionALL Settings to Midpos Undo ALL Settings to MidposUndo R & B convergence mid Convergence midGreen convergence mid Undo green convergence midG2 Adjustment Common SettingsCommon Settings G2 AdjustmentProjector warm up CRT Drive ModeProjector Warm UP Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode I2C error Addr FH3 Enter Password Text on Text offFh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just rangeIris commu Nication Error Rcvds com Munication ErrorProjector Will Switch off StartingOptions Line Doubler Kit Magik Interface Orbiting KitCeiling mount CM50 Adapter and communication cablesSource numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Barcodata 708 Insert Card