Barco R9002120 manual How to use the RCU, Projector address, How to display a projector address?

Page 22

Controlling

The projector can be controlled with a. The RCU

b. The hardwired RCU (cable not included) c. The local keypad.

Controlling the projector with the RCU and the hardwired RCU is the same.

How to use the RCU

a) Point the front of the RCU towards the reflective screen surface

Ceiling

IR sensor

Screen

c) RCU used in a hardwired configuration.

 

RS232IN

RS232OUT

IR COMM PORT

R

G(S)

B

S VIDEO

S- VIDEO

 

 

 

(800 peripherals) REMOTE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

219

Plug one end of the remote cable in the connector on the bottom of the RCU and the second side in the connector in the rear panel of the projector labelled 'REMOTE'.

b)Point the front of the RCU towards one of the IR sensors in the projector.

When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the projector's IR sensor.

Front of projector

Rear side of projector

Projector address

a. Software set up of the projector address.

See 'Change Projector Address' in chapter 'Service mode'.

Every projector requires an individual address between 0 and 255 which is set in the Service mode. Only projectors with addresses between 0 and 9 can be controlled with the RCU.

b. How to control the projector.

The projector's address may be set to any value between 0 and 255. When the address is set, the projector can be controlled with :

-the RCU for addresses between 0 and 9.

-Computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.

Note : A projector will respond to an RCU set to an address of '0' regardless of what address is set in the projector itself.

c. Using the RCU.

45°

45°

45°

45°

 

 

ENTER

9

0

 

 

 

RCU

9

0

 

 

 

 

 

 

7

8

7

8

 

 

5

6

5

6

 

 

3

4

3

4

 

 

1

2

1

2

 

 

Before using the RCU, it is necessary to enter the projector address into the RCU (only when that address is between 1 and 9). The projector with the corresponding address will listen to that specific RCU.

When address 0, 'zero address' is programmed into the RCU, every projector, without exception will listen to the commands given by this RCU.

How to display a projector address?

Press the ADDRESS key (recessed key on the RCU) with a pencil. The projector's address will be displayed in a 'Text box'. This text box disappears after a few seconds.

PROJECTOR

ADDRESS

001

4-2

 

5975977 BARCODATA 708 260597

 

Image 22
Contents R9002120 Page Barco Projection Systems Date Art. No 260597 R5975977Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Start UP of the Adjustment Mode Options Table of Contents Safety Instructions On safetyOn servicing On installationOn cleaning On repackingRear Panel Terminology Location and Function of ControlsFront Panel Terminology Control panel terminology a. The local keypad Gaining accessAdjustexit RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Signal input connection to the projector Power mains cord connectionSwitching on/off ConnectionsSource No Projector input Press digit button Connecting a Composite Video sourceVideo input selection Connecting a S-Video or Video source to port Input selectionConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection RGB3S or RG3sB input selection Connecting a Component sourceConnecting a Component source with Tri-level sync YYB-YS orR-YYsB-Y input selectionRemote control Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector YYB-Y3S or R-YY3sB-Y input selectionBattery installation in the RCU ControllingHow to display a projector address? How to use the RCUProjector address How to program an address into the RCU? Input selection Source No Projector input Press buttonPicture controls Pause keyAdjustment mode Adjustexit StandbyenterPassword WrongStarting up the random access adjustment mode Overview random Access Adjustment modeInternal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Sync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Line Doubler optionPort 2 S-Video/Video Color SelectGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments BlankingConvergence Adjustment Random Access Adjustment Mode Starting up the Service mode Overview flowchart Service modeIdentification Projector Set-upData Total Run Time Change passwordChange Language Change baudrate Power up modeChange Projector Address BaudrateBarco Logo BARCOlogoMemory management Memory ManagementDeletion of blocks Copy a blockDeleting block by block ALL Settings to Midpos All settings to midpositionUndo all settings to midpos Undo ALL Settings to MidposGreen convergence mid Convergence midUndo R & B convergence mid Undo green convergence midCommon Settings Common SettingsG2 Adjustment G2 AdjustmentProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPI2C Diagnostics Permanent Boost Mode USEService Mode Fh= 15.6 kHz Fv= 050 Hz Enter Password Text on Text offI2C error Addr FH3 Invalid Code entry End of ad- just rangeProjector Will Switch off Rcvds com Munication ErrorIris commu Nication Error StartingOptions Ceiling mount CM50 Magik Interface Orbiting KitLine Doubler Kit Adapter and communication cablesAdjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Barcodata 708 Insert Card