Barco R9002120 manual Projector warm up, CRT Drive Mode, Projector Warm UP

Page 48

Service Mode

If a memory block adjusted on an internal # pattern is available, the CRT run in cycle will start when pressing ENTER. If no such a block is available, the projector cannot run the CRT run in option and leaves the adjustment mode.

If you still want to run CRT run in cycle, create first a memory block on an internal # pattern and restart the CRT run in option.

ENTER starts the 'CRT run in' when an internal generated # pattern is available.

EXIT returns to the Path Selection main menu.

Projector warm up

Highlight 'Projector warm up' by pushing the control disk up or down and press ENTER to select the projector warm up menu.

The ON/OFF option can be toggled with the ENTER key.

When in the ON position (and the CRT run in cycle is OFF), the projector can start up with a warm up periode of 20 minutes. During the start up a warm up menu will be displayed. This menu offers the possibility to skip the warm up periode anyway by pressing the EXIT key and offers the possibility to adjust the horizontal and vertical amplitude of this white image with the control disk. During this warm up period, a full white image is shifted on the CRT faceplate to avoid a burn in.

Every 30 seconds a text box will be displayed on another place on the screen with the remaining time to go.

When EXIT is pressed during this warm up periode, the warm up menu will be redisplayed with the remaining time indication. Press another time EXIT to interrupt the warm up cycle.

When the warm up option is OFF, when switching on the projector, it starts immediately with the projection of the selected source.

CRT Drive Mode

The projector CRT's can be driven with the normal current (normal mode), a lower current (economic mode) or with a higher current (boost mode).

To change the drive mode, highlight 'CRT drive mode' by pushing the control stick forward or backward and press ENTER to display the CRT drive mode menu.

To change the boost mode, push the control disk up or down to select a display mode and press ENTER to select.

The following modes are available :

-Normal

-Economic : Lower drive current to the CRT's, the lifetime of the CRT's will enlarge but the light output will reduce.

-Tempory boost : Higher drive current to the CRT's, the lifetime of the CRT's will shorten but the light output will be higher. This situation is tempory, when restarting the projector, the drive mode is auto- matically set to normal.

-Permanent boost : Higher drive current to the CRT's, the lifetime of the CRT's will shorten but the light output will be higher. This setting will be saved in the EEPROM. When restarting the projector, it will start up in boost mode.

CRT RUN IN CYCLE

A flashing white pattern

will be generated until <EXIT> is pressed.

The projector only uses memory blocks adjusted on an internal # pattern;

if no such block is

available, the projector

can't run the procedure and leaves the adjustment mode.

<ENTER> to continue <EXIT> to cancel

COMMON SETTINGS

G2 ADJUSTMENT

CRT RUN IN CYCLE

PROJECTOR WARM UP

CRT DRIVE MDOE

Select with or then <ENTER> <EXIT> to return.

PROJECTOR WARM UP

OPTION : ON

A FULL WHITE PATTERN WILL BE GENERATED FOR 20 MINUTES AT POWER UP AFTER THIS PROCEDURE THE PROJECTOR IS READY

TO PERFORM IN OPTIMUM

CONDITION

TOGGLE OPTION ON OR OFF

with <ENTER> <EXIT> to return

COMMON SETTINGS

 

G2 ADJUSTMENT

 

CRT RUN IN CYCLE

 

PROJECTOR WARM UP

 

CRT DRIVE MDOE

 

CRT DRIVE MODE

NORMAL

ECONOMIC

TEMPORARY BOOST

PERMANENT BOOST

WARNING : permanent

boost mode reduces the lifetime

of the CRT's !

Select with

or

then <ENTER>

<EXIT> to return.

7-10

 

5975977 BARCODATA 708 280597

 

Image 48
Contents R9002120 Page Barco Projection Systems Date Art. No 260597 R5975977Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Start UP of the Adjustment Mode Options Table of Contents Safety Instructions On safetyOn installation On cleaningOn servicing On repackingLocation and Function of Controls Rear Panel TerminologyFront Panel Terminology Gaining access AdjustexitControl panel terminology a. The local keypad RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Power mains cord connection Switching on/offSignal input connection to the projector ConnectionsConnecting a Composite Video source Source No Projector input Press digit buttonVideo input selection Connecting a S-Video or Video source to port Input selectionConnecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection Connecting a Component source Connecting a Component source with Tri-level syncRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selectionConnecting a VS05 switcher to the projector Connecting an IR Remote Receiver to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selectionBattery installation in the RCU ControllingHow to use the RCU How to display a projector address?Projector address How to program an address into the RCU? Input selection Source No Projector input Press buttonPicture controls Pause keyAdjustment mode Adjustexit StandbyenterPassword WrongStarting up the random access adjustment mode Overview random Access Adjustment modeSelecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Random access adjustment mode selection menu Picture TuningSync Fast/Slow Adjustment Color BalanceLine Doubler option Port 2 S-Video/VideoPeaking Color SelectGeometry Adjustments Horizontal Phase AdjustmentGeometry GeometryRaster Shift Adjustment Projected rasterCrt faceplate border Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT E-W Top-Bottom north-south Adjustments TOP-BOTTOMTOP-BOTTOM N-S TOP-BOTTOM N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Adjustments BlankingConvergence Adjustment Random Access Adjustment Mode Starting up the Service mode Overview flowchart Service modeProjector Set-up IdentificationData Change password Total Run TimeChange Language Power up mode Change Projector AddressChange baudrate BaudrateBARCOlogo Memory managementBarco Logo Memory ManagementCopy a block Deletion of blocksDeleting block by block All settings to midposition Undo all settings to midposALL Settings to Midpos Undo ALL Settings to MidposConvergence mid Undo R & B convergence midGreen convergence mid Undo green convergence midCommon Settings G2 AdjustmentCommon Settings G2 AdjustmentCRT Drive Mode Projector warm upProjector Warm UP Projector Warm UPI2C Diagnostics Permanent Boost Mode USEService Mode Enter Password Text on Text off I2C error Addr FH3Fh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just rangeRcvds com Munication Error Iris commu Nication ErrorProjector Will Switch off StartingOptions Magik Interface Orbiting Kit Line Doubler KitCeiling mount CM50 Adapter and communication cablesAdjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Barcodata 708 Insert Card