Barco R9002120 manual Total Run Time, Change password, Change Language

Page 41

Service Mode

Total Run Time

Highlight 'Total Run Time' with the control disk and press ENTER to display the amount of time the projector has played since its first start up at the factory.

ENTER gives the selected item.

EXIT returns to the Service mode menu.

ADJUST returns to the Operational mode.

Note : all projectors leave the factory after a burn-in period of approximately 100 hours.

Change password

This item is password protected.

Highlight 'Change Password' with the control disk and press ENTER.

ENTER will display the selected item.

EXIT will return to the Path Selection main menu.

ADJUST will return to the Operational mode.

The current password is displayed. The new password must consist of 4 digits between 0 and 9. Push the control disk to the left or to the right to select the digits to be changed. Use the numeric keys to enter the new digits.

Press ENTER to save the new password. Before saving the new password, a confirmation screen will be displayed.

Press EXIT to return to the Projector Set-up menu without saving the new password.

When the displayed password is correct, press ENTER to save. If not correct, press EXIT to cancel the saving.

ENTER saves the entered password.

EXIT returns without saving.

PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with	or
then <ENTER>
<EXIT> to return.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE : operating

BARCO LOGO

PASSWORD

Enter new password :

0 0 0 0

Use

CHANGE PASSWORD

Password will be

reprogrammed as xxxx

<ENTER> to confirm

<EXIT> to cancel

Change Language

The 'Change Language' function offers the possibility to change the language of the screen menus to :

-English

-Spanish

-French

-German

Highlight 'Change Language' with the control disk and press ENTER.

ENTER selects the Change language menu.

EXIT returns to the Service menu.

Push the control disk up or down to select the desired language and press ENTER to change the language.

PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
LANGUAGE
ENGLISH
ESPAÑOL
FRANCAIS
DEUTSCH
Select with	or
then <ENTER>
<EXIT> to return.

5975977 BARCODATA 708 260597		7 - 3

Image 41

Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn cleaning On installationOn servicing On repackingFront Panel Terminology Location and Function of ControlsRear Panel Terminology Adjustexit Gaining accessControl panel terminology a. The local keypad RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Switching on/off Power mains cord connectionSignal input connection to the projector ConnectionsVideo input selection Connecting a Composite Video sourceSource No Projector input Press digit button Input selection Connecting a S-Video or Video source to portRgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync Connecting a Component source with Tri-level sync Connecting a Component sourceRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selectionConnecting an IR Remote Receiver to the projector Connecting a VS05 switcher to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selectionControlling Battery installation in the RCUProjector address How to use the RCUHow to display a projector address? Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeInternal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Picture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalancePort 2 S-Video/Video Line Doubler optionPeaking Color SelectHorizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeData Projector Set-upIdentification Change Language Change passwordTotal Run Time Change Projector Address Power up modeChange baudrate BaudrateMemory management BARCOlogoBarco Logo Memory ManagementDeleting block by block Copy a blockDeletion of blocks Undo all settings to midpos All settings to midpositionALL Settings to Midpos Undo ALL Settings to MidposUndo R & B convergence mid Convergence midGreen convergence mid Undo green convergence midG2 Adjustment Common SettingsCommon Settings G2 AdjustmentProjector warm up CRT Drive ModeProjector Warm UP Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode I2C error Addr FH3 Enter Password Text on Text offFh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just rangeIris commu Nication Error Rcvds com Munication ErrorProjector Will Switch off StartingOptions Line Doubler Kit Magik Interface Orbiting KitCeiling mount CM50 Adapter and communication cablesSource numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Barcodata 708 Insert Card