Barco R9002120 manual Connecting a Component source with Tri-level sync

Page 19

Connections

RGB3S or RG3sB input selection

a. Press digit button 4 on the RCU or

b. With the local keypad :

(to gain access to the local keypad, see 'Local keypad' in chapter 'Location and function of controls'.)

-Press ADJUST key, the General access menu is displayed on the screen.

-Use the control disk to highlight 4.

-Press ENTER to select the highlighted source.

	GENERAL ACCESS
		SHARPNESS
		TINT
5	6	COLOR
3	4	BRIGHTNESS
1	2	CONTRAST

Enter ADJUST

Select with	,
	or
then <ENTER>.

<EXIT> to return

Connecting a Component source.

(R-Y)Y(B-Y) analog input terminals with sync input or with sync on the luminance (Y) input. The projector detects automatically where the sync signal is located.

Line doubling is possible for component video input sources on standard line frequency.

If a line doubler is built in :

the default position of this line doubler is ON (active), the component video input signal will be displayed as a non interlaced image (= improved image stability).

To enable or to disable this line doubler function, enter the adjustment mode and change the position of the ON/OFF toggle switch (see Picture tuning in chapter 'Guided' adjust- ment mode or 'Random access' adjustment mode).

(R-Y)Y(B-Y)S or(R-Y)Ys(B-Y) input selection

a. Press digit button 5 on the RCU or

b. With the local keypad :

(to gain access to the local keypad, see 'Local keypad' in chapter 'Location and function of controls'.)

-Press ADJUST key, the General access menu is displayed on the screen.

-Use the control disk to highlight 5.

-Press ENTER to select the highlighted source.

RS232 IN

RS232 OUT

COMM PORT

R

G(S)

B

S VIDEO

S-VIDEO

(800 peripherals) REMOTE

R-Y

Y(S)

B-Y

Professional VCR

Audio amplifier

	GENERAL ACCESS
		SHARPNESS
		TINT
5	6	COLOR
3	4	BRIGHTNESS
1	2	CONTRAST

Enter ADJUST

Select with	,
	or
then <ENTER>.

<EXIT> to return

Connecting a Component source with Tri-level sync.

(R-Y)Y(B-Y) analog input terminals with Tri-level sync input or with Tri-level sync on the luminance input.

RS232 IN

RS232 OUT

COMM PORT

R

G(S)

B

S VIDEO

S-VIDEO

(800 peripherals) REMOTE

R-Y

Y(S)

B-Y

Professional VCR	Audio amplifier
with Tri-level sync

5975977 BARCODATA 708 260597		3 - 5

Image 19

Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn repacking On installationOn cleaning On servicingRear Panel Terminology Location and Function of ControlsFront Panel Terminology RCU control panel terminology Gaining accessAdjustexit Control panel terminology a. The local keypadLocation and Function of Controls Location and Function of Controls Connections Power mains cord connectionSwitching on/off Signal input connection to the projectorSource No Projector input Press digit button Connecting a Composite Video sourceVideo input selection Input selection Connecting a S-Video or Video source to portConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection YYB-YS orR-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RGB3S or RG3sB input selectionYYB-Y3S or R-YY3sB-Y input selection Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Remote controlControlling Battery installation in the RCUHow to display a projector address? How to use the RCUProjector address Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeInternal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select Line Doubler optionPort 2 S-Video/Video PeakingGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Raster Shift AdjustmentProjected raster Crt faceplate borderLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeIdentification Projector Set-upData Total Run Time Change passwordChange Language Baudrate Power up modeChange Projector Address Change baudrateMemory Management BARCOlogoMemory management Barco LogoDeletion of blocks Copy a blockDeleting block by block Undo ALL Settings to Midpos All settings to midpositionUndo all settings to midpos ALL Settings to MidposUndo green convergence mid Convergence midUndo R & B convergence mid Green convergence midG2 Adjustment Common SettingsG2 Adjustment Common SettingsProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode Invalid Code entry End of ad- just range Enter Password Text on Text offI2C error Addr FH3 Fh= 15.6 kHz Fv= 050 HzStarting Rcvds com Munication ErrorIris commu Nication Error Projector Will Switch offOptions Adapter and communication cables Magik Interface Orbiting KitLine Doubler Kit Ceiling mount CM50Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Barcodata 708 Insert Card