Barco R9002120 manual Projector Set-up, Identification, Data

Page 40

Service Mode

Projector Set-up

Highlight 'Projector Set-Up'by pushing the control disk up or down and press ENTER to display the projector set-up menu.

Within the projector set-up menu, the fol- lowing items can be consultated or set to the desired setting :

-Identification

-Total run time

-Change password

-Change language

-Change projector address

-Change baudrate

-Power up mode

-BARCO logo

SERVICE MODE

 

PROJECTOR SET-UP

 

MEMORY MANAGEMENT

 

COMMON SETTINGS

 

I2C DIAGNOSTICS

 

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE : operating

BARCO LOGO

Select with

or

then <ENTER>

<EXIT> to return.

Identification

Highlight 'Identification' with the control disk and press ENTER.

ENTER will start the selected item.

EXIT returns to the Service mode menu.

The 'Identification' screen gives information concerning :

-Projector address. To change the address of your projector, contact a qualified service technician.

-Software version.

-Configuration.

Possible installations :

*Front-ceiling

*Front-table

*Rear-ceiling

*Rear-table

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE : operating

BARCO LOGO

DATA 708

Proj. address : 001

Soft. Version : 6.00

Config. : Ceiling

Front

Baudrate PC : 9600

Text : ON

Serial No. : 103589552

-Baud rate PC : transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, contact a qualified service technician to make the appropriate changes.

-Text ON/OFF

Indicates in operational mode if the bar scale and number indicator will be displayed and if warnings and failures will be displayed. ON : displayed

OFF : not displayed

The status can be changed by pressing the 'TEXT' key once on the RCU.

-Serial no. : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

7 - 2

 

5975977 BARCODATA 708 280597

 

Image 40
Contents R9002120 Page Barco Projection Systems Date Art. No 260597 R5975977Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Start UP of the Adjustment Mode Options Table of Contents Safety Instructions On safetyOn installation On cleaningOn servicing On repackingRear Panel Terminology Location and Function of ControlsFront Panel Terminology Gaining access AdjustexitControl panel terminology a. The local keypad RCU control panel terminologyLocation and Function of Controls Location and Function of Controls Power mains cord connection Switching on/offSignal input connection to the projector ConnectionsSource No Projector input Press digit button Connecting a Composite Video sourceVideo input selection Connecting a S-Video or Video source to port Input selectionConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection Connecting a Component source Connecting a Component source with Tri-level syncRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selectionConnecting a VS05 switcher to the projector Connecting an IR Remote Receiver to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selectionBattery installation in the RCU ControllingHow to display a projector address? How to use the RCUProjector address How to program an address into the RCU? Input selection Source No Projector input Press buttonPicture controls Pause keyAdjustment mode Adjustexit StandbyenterPassword WrongStarting up the random access adjustment mode Overview random Access Adjustment modeInternal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Random access adjustment mode selection menu Picture TuningSync Fast/Slow Adjustment Color BalanceLine Doubler option Port 2 S-Video/VideoPeaking Color SelectGeometry Adjustments Horizontal Phase AdjustmentGeometry GeometryRaster Shift Adjustment Projected rasterCrt faceplate border Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W Top-Bottom north-south Adjustments TOP-BOTTOMTOP-BOTTOM N-S TOP-BOTTOM N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments BlankingConvergence Adjustment Random Access Adjustment Mode Starting up the Service mode Overview flowchart Service modeIdentification Projector Set-upData Total Run Time Change passwordChange Language Power up mode Change Projector AddressChange baudrate BaudrateBARCOlogo Memory managementBarco Logo Memory ManagementDeletion of blocks Copy a blockDeleting block by block All settings to midposition Undo all settings to midposALL Settings to Midpos Undo ALL Settings to MidposConvergence mid Undo R & B convergence midGreen convergence mid Undo green convergence midCommon Settings G2 AdjustmentCommon Settings G2 AdjustmentCRT Drive Mode Projector warm upProjector Warm UP Projector Warm UPI2C Diagnostics Permanent Boost Mode USEService Mode Enter Password Text on Text off I2C error Addr FH3Fh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just rangeRcvds com Munication Error Iris commu Nication ErrorProjector Will Switch off StartingOptions Magik Interface Orbiting Kit Line Doubler KitCeiling mount CM50 Adapter and communication cablesAdjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Barcodata 708 Insert Card