Barco R9002120 manual Connections, Power mains cord connection, Switching on/off, Hold Down

Page 15

Connections

3 CONNECTIONS

Power (mains) cord connection

Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector.

			See installation instructions before
			connecting to the supply
				V NOM 120/230 Volt
				I MAX	5/2.5 AMP
			OFF ON	FREQ	60/50 Hz
See installation instructions before
connecting to the supply
		V NOM 120/230 Volt
		I MAX	5/2.5 AMP
OFF	ON	FREQ	60/50 Hz
OFF	ON

Switching on/off

The projector is switched ON and OFF using the power (mains) switch ON/OFF.

Pressed : ON

Not pressed : OFF

The projector can start now in the 'operational mode' (image displayed) or in the 'stand by mode', depending on the position of the 'power up' dip switch on the controller unit. This DIP switch is set during installation by a qualified technician. If you want to change this start up mode, call a qualified technician.

Leds on the front plate of the projector

-CONV	+9V +17V	+210V -9V +30V	-17V +HTHD +CONV	STANDBY	HOLD DOWN	SF	COINC	HOLD DOWN
					EHT			HD

Signal input connection to the projector :

-Composite Video (*)

-S-Video (*)

-RGBS or RGsB

-RGB3S or RG3sB

-(R-Y)Y(B-Y)S or (R-Y)Ys(B-Y) [component input] (**)

-(R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) [component input] (**)

(*)If the line double feature is built in, this feature is available via a software on/off toggle.

(**)If the line double feature is built in, this feature is available for component video signals on standard frequency via software on/off toggle.

	RS232 IN	RS232 OUT	COMM PORT			R	G(S)	B	S	VIDEO	S-VIDEO
	RS232 IN	RS232 OUT	(800 peripherals ) REM O T E			R-Y	Y( S)	B-Y	S	VIDEO

3 1 2

5975977 BARCODATA 708 260597		3 - 1

Image 15

Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn repacking On installationOn cleaning On servicingLocation and Function of Controls Rear Panel TerminologyFront Panel Terminology RCU control panel terminology Gaining accessAdjustexit Control panel terminology a. The local keypadLocation and Function of Controls Location and Function of Controls Connections Power mains cord connectionSwitching on/off Signal input connection to the projectorConnecting a Composite Video source Source No Projector input Press digit buttonVideo input selection Input selection Connecting a S-Video or Video source to portConnecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection YYB-YS orR-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RGB3S or RG3sB input selectionYYB-Y3S or R-YY3sB-Y input selection Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Remote controlControlling Battery installation in the RCUHow to use the RCU How to display a projector address?Projector address Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeSelecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select Line Doubler optionPort 2 S-Video/Video PeakingGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Raster Shift AdjustmentProjected raster Crt faceplate borderLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeProjector Set-up IdentificationData Change password Total Run TimeChange Language Baudrate Power up modeChange Projector Address Change baudrateMemory Management BARCOlogoMemory management Barco LogoCopy a block Deletion of blocksDeleting block by block Undo ALL Settings to Midpos All settings to midpositionUndo all settings to midpos ALL Settings to MidposUndo green convergence mid Convergence midUndo R & B convergence mid Green convergence midG2 Adjustment Common SettingsG2 Adjustment Common SettingsProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode Invalid Code entry End of ad- just range Enter Password Text on Text offI2C error Addr FH3 Fh= 15.6 kHz Fv= 050 HzStarting Rcvds com Munication ErrorIris commu Nication Error Projector Will Switch offOptions Adapter and communication cables Magik Interface Orbiting KitLine Doubler Kit Ceiling mount CM50Adjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Barcodata 708 Insert Card