Barco R9002120 manual Starting up the random access adjustment mode

Page 27

Random Access Adjustment Mode

6	RANDOM ACCESS ADJUSTMENT MODE

Starting up the random access adjustment mode.

Push the control disk up or down to highlight "RANDOM AC- CESS" and then press ENTER.

Some items in the Random access mode are password protected (when the password function is enabled). Enter your password to continue. All other password protected items are now also available if you stay in the adjustment mode.

ENTER continues to Setup Pattern Selection

EXIT returns to operational mode

ADJUSTMENT MODE

Select a path from below:

GUIDED RANDOM ACCESS

INSTALLATION

SERVICE

IRIS

source 1

Select with or then <ENTER> <EXIT> to return

Overview 'random Access Adjustment' mode.

RANDOM ACCESS ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

COLOR BALANCE

SYNC

LINE DOUBLER

PORT 2

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

V CENTERLINE BOW

V CENTERLINE SKEW

SIDE BOW

SIDE KEYSTONE

SEAGULL CORRECTION

SETUP PATTERN SELECTION

CONVERGENCE

COLOR SELECT

5975977 BARCODATA 708 260597

TOP-BOTTOM (N-S)

SIZE

VER LINEARITY

BLANKING

H CENTERLINE BOW

H CENTERLINE SKEW

TOP KEYSTONE

TOP BOW

BOTTOM KEYSTONE

BOTTOM BOW

SEAGULL CORRECTION

TOP BOW

BOTTOM KEYSTONE

BOTTOM BOW

SEAGULL CORRECTION

6-1

Image 27

Contents R9002120 Page Date Art. No 260597 R5975977 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety InstructionsOn repacking On installationOn cleaning On servicingLocation and Function of Controls Rear Panel TerminologyFront Panel Terminology RCU control panel terminology Gaining accessAdjustexit Control panel terminology a. The local keypadLocation and Function of Controls Location and Function of Controls Connections Power mains cord connectionSwitching on/off Signal input connection to the projectorConnecting a Composite Video source Source No Projector input Press digit buttonVideo input selection Input selection Connecting a S-Video or Video source to portConnecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection YYB-YS orR-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RGB3S or RG3sB input selectionYYB-Y3S or R-YY3sB-Y input selection Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Remote controlControlling Battery installation in the RCUHow to use the RCU How to display a projector address?Projector address Input selection Source No Projector input Press button How to program an address into the RCU?Pause key Picture controlsAdjustexit Standbyenter Adjustment modeWrong PasswordOverview random Access Adjustment mode Starting up the random access adjustment modeSelecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentColor Select Line Doubler optionPort 2 S-Video/Video PeakingGeometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Raster Shift AdjustmentProjected raster Crt faceplate borderLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Blanking AdjustmentsConvergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service modeProjector Set-up IdentificationData Change password Total Run TimeChange Language Baudrate Power up modeChange Projector Address Change baudrateMemory Management BARCOlogoMemory management Barco LogoCopy a block Deletion of blocksDeleting block by block Undo ALL Settings to Midpos All settings to midpositionUndo all settings to midpos ALL Settings to MidposUndo green convergence mid Convergence midUndo R & B convergence mid Green convergence midG2 Adjustment Common SettingsG2 Adjustment Common SettingsProjector Warm UP CRT Drive ModeProjector warm up Projector Warm UPPermanent Boost Mode USE I2C DiagnosticsService Mode Invalid Code entry End of ad- just range Enter Password Text on Text offI2C error Addr FH3 Fh= 15.6 kHz Fv= 050 HzStarting Rcvds com Munication ErrorIris commu Nication Error Projector Will Switch offOptions Adapter and communication cables Magik Interface Orbiting KitLine Doubler Kit Ceiling mount CM50Adjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Barcodata 708 Insert Card