APC AP9208, AP9608 manual UPS Cable External Version, Power Port External Version

Page 7

2.4 UPS Cable [External Version]

Use this cable to connect Call-UPSII to an APC Smart-UPS, Matrix-UPS, Symmetra Power Array or other APC smart device (Share-UPSor Triple Chassis, for example).

2.5 Power Port [External Version]

The external version of Call-UPSII has a power port for an optional power adapter. This adapter is not needed in most situations. Call-UPSII normally receives power from the UPS through the UPS connection cable, giving Call-UPSII protection from poor power conditions. After UPS shutdown for low-battery condition, Call-UPSII will still draw power from the UPS for a time determined by the size of the load and the capac- ity of the UPS. However, Call-UPSII stops drawing power from the UPS before the battery is completely drained.

To determine whether a power connector will be useful, refer to the two paragraphs that follow. You can obtain a power adapter by contacting APC technical support at one of the numbers given on the back cover of this manual. The APC part number for the power adapter is AP9505.

With Smart-UPS

The optional power adapter is required for some older Smart-UPSmodels that do not supply power to Call-UPSII. To determine whether your Smart-UPSsupplies power to Call-UPSII, refer to the Smart-UPSuser manual. Plug the adapter into a wall receptacle if you want remote turn- on and turn-off capability; otherwise, plug it into a Smart -UPSreceptacle. (Smart-UPSmodels 250, 370, and 400 cannot be turned on or off by remote connection; for these models plug the adapter into a Smart-UPSreceptacle.)

With Matrix-UPS

You will need the optional power adapter for use with Matrix-UPSonly if you want remote turn-on capability. Matrix-UPScan be turned off remotely by Call-UPSII, but, without the adapter, Call-UPSII will then lose power. The UPS will execute a Graceful Reboot command (item 5 on the UPS Control menu of Call-UPSII ) without causing Call-UPSII to lose power. Plug the power adapter into a wall receptacle if you want remote turn-on and turn-off capability. Otherwise, plug it into a Matrix-UPSreceptacle.

3

Image 7
Contents Call-UPSII Thank You Contents Problem Resolution Overview IntroductionHardware Requirements UPS Monitoring Port External Version Product DescriptionCall-UPS II Panel Management PortUPS Cable External Version Power Port External VersionWith Smart-UPS With Matrix-UPS Status LED Indication Status IndicatorReceiving Inspection Installation and SetupInstallation HandlingExternal Version Confirm OperationInitial Logging On Configure Call-UPSPress any key to bring up the Main menu Customize SettingsConnect to Modem SmartSlot Configuration External Configuration Operation UPS Status and DiagnosticsLogging On to Call-UPS With Smart-UPS and Matrix-UPS UPS Status Smart-UPS and Matrix-UPS Description Sleeping Inverter Shutdown UPS Status and Diagnostics Symmetra Power Array Description With Symmetra Power ArrayUPS Status and Diagnostics Page RIM Page UPS Control Command DescriptionUPS Control UPS Control UPS Characteristics Call-UPS II will not allow changes to UPS characteristics Sensitivity of the UPS to power line fluctuation. Set this With Symmetra Power Array UPS Characteristics Symmetra Power Array Setting Description Menu Data/Event LoggingDATA/EVENT Logging Default DescriptionCALL-UPS Call-UPS SettingsCALL-UPS II Settings CALL-UPS II Settings Default Description Site IDspace charactertrouble code Paging SetupPaging Setup Paging Setup Setting Default Description Event Description Paging Setup EventsProbe Measure-UPS InfoMEASURE-UPS Info Problem Possible Cause Solution Problem ResolutionTroubleshooting Chart TroubleshootingIf Problems Persist Management Port Pinout SpecificationsPin Function Environmental Product SpecificationsElectrical PhysicalDevice Priority Position Appendix Multiple SmartSlot InstallationTriple Chassis Daisy Chains Symmetra Power ArraySmart-UPS and Matrix-UPS Page Page Page Limited Warranty Toll free technical support