Vixel 335 manual System LEDs Indication, Port LEDs

Page 10

Vixel Model 335 Installation & Configuration Guide

CHAPTER 2 Installation

 

 

 

 

 

 

 

 

 

 

 

System LEDs

 

Indication

 

 

 

 

 

 

Power

When lit, the switch is plugged in and the internal power

 

 

(green LED)

supply is functional.

 

 

 

 

 

 

 

Switch Fault

Indicates that the internal hardware self-test failed. When

 

 

(yellow LED)

lit, the switch will not function. -or-

 

 

 

Indicates that a fan has stopped operating or the ambient

 

 

 

temperature has exceeded 45°C. When lit, the switch is still

 

 

 

functional but requires immediate attention. The LED will

 

 

 

turn off when the detected condition is corrected.

 

 

 

 

 

 

Switch Op

Indicates whether the zones are initialized and operational.

 

 

(green LED)

If the Switch Op LED is lit, all zones with inserted devices

 

 

 

are operational. If the Switch Op LED is blinking in a

 

 

 

multiple zone configuration, one or more zones are

 

 

 

operational while others are not. If the Switch Op LED is

 

 

 

off, no operational zones exist or no devices are attached.

 

 

 

 

 

 

2 Gb/s

Indicates the current operational speed of the switch. When

 

 

(green LED)

lit, the switch is operating at 2 Gb/s. If unlit, the switch is

 

 

 

operating at 1 Gb/s.

 

 

 

 

 

 

 

Mgmt Present

Indicates that switch management is functioning. If

 

 

(yellow LED)

flashing, indicates that management functionality has failed

 

 

 

and is not communicating with the switch.

 

 

 

 

 

 

Enet Active

Indicates Ethernet activity on the switch and is controlled

 

 

(green LED)

through the Ethernet transceiver.

 

 

 

 

 

 

Port LEDs

Port LEDs indicate the current status of the particular port.The switch uses two port

LEDs: SFP Status and Port Bypassed/Port Activity. The Port Bypassed and Port Activity

LEDs share the same yellow/green LED.

Figure 2-3. Port LEDs

7

Image 10
Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents About This Guide FeaturesIntroduction OverviewFibre Channel Arbitrated Loop InSpeed TechnologyUnpacking the Switch InstallationInstalling the Switch Small Form-Factor Pluggable SFP Installation Using Small Form Factor Pluggable SFP TransceiversPerforming a Power On Systems Test Small Form-Factor Pluggable SFP RemovalSetting Up the Switch Attaching DevicesPower On Understanding the Switch’s LEDsSystem LEDs System LEDs Indication Port LEDsSFP Cascading Switches Cascading with Non-Overlapping ZonesAcceptable Single Cascade in Zones 2-12 Only Connecting to the Web Manager Using the Web ManagerE rv i e w Navigation Logging On and OffConfiguration Task Location in Web Manager Configuring the SwitchResetting the Switch System Information Settings Setting DescriptionNetwork Settings Click Change SettingsSwitch Identification Switch SpeedSwitching Mode Blocking ARBDownloading the Switch Configuration Time SettingsFirmware Settings Firmware InformationClick Change Firmware Settings Event Log MessagesFC Switch Information FC Switch InformationOS Information Detection IndicationCLS Port Usage Information 11.Ordered Set Information Page with Highlighted ZonesValue Description 13.Received Port Utilization Page with Highlighted ZonesPort Settings 15.Port Information16.Port Information Page with Highlighted Zones Mode Description 18.Cascade Information19.Cascade Information Page with Highlighted Zones Policy Settings Switch Policy Description21.Policies Change Settings Zone Settings 22.Overlapping ZonesOverlapping Zones 25.Overlapping Zone 1 Information26.Overlapping Zone 1 Information Configuration Non-Overlapping ZonesClick Back to Non-overlapping Zone Info to view the changes Management Using the Command Line Interface CLI Connecting to the CLIConfiguration Task CLI Command NozConfiguring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling Dhcp Requests Managing the Firmware Downloading New FirmwareMessage Action Configuring the Trap Destination Table Edit Trap Destination Menu Active Value NEW ValueOption Description Changing the CLI/Web Password Viewing Management, Policy, and Threshold SettingsPolicies Policy DescriptionSettings Description Threshold InformationActions Action DescriptionChanging the Switching Mode Command DescriptionNumber. You can also change the port policies Displaying Ports PLLEnables you to configure control of the port. Select from Resetting the Switch to Factory Default Settings Resetting the SwitchResetting the Hardware Viewing the Event LogOverlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10Reference Technical SupportTro ub l e sh oo ti n g Small Form-Factor Pluggable SFP Issues Fibre Channel ReferencesAppendixes Appendix a Specifications Specification sOperating Conditions Vixel Model 335 Operating ConditionsGeneral Commands CommandsConsole Commands Browse CommandsAction Commands Show ZoneURL Appendix C Event Messages Event Meaning Action Severity MessageAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Configuring switch information IndexIndex
Related manuals
Manual 74 pages 62.9 Kb