Vixel 335 manual Firmware Settings, Firmware Information

Page 21

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

Note: Clicking Back on the browser tool bar may not update settings due to web browser caching pages in memory.

To change the Time Mode:

1. From the Time Mode drop-down box, select the desired time setting.

Setting	Description

none	The switch does not set the time.

Server	The switch receives the time from a time server via
	Ethernet.

User	The user manually sets the time for the switch.

2.Click Submit. To use a time server:

1.Select Server in the Time Mode drop-down box.

2.Enter the IP Address for the time server in the Time Server text box.

3.Enter the desired update interval in minutes in the Time Server Update Interval (min) text box.

4.Click Sync to Server Time to immediately synchronize the server time to the time server at the designated IP Address.

5.Click Submit.

To set the time setting to the computer connected to the switch, click the Sync to PC Time Now Sync button and then click Submit.

To view the new time settings, click Back to Time page.

Firmware Settings

The Firmware page displays information on the current firmware version, the alternate firmware version, and the version of the software that loads the firmware image on boot up.

To view the current firmware settings:

1.Click System. The System Information page appears.

2.Click Firmware. The Firmware Information page appears.

Figure 3-6.Firmware Information Page

18

Image 21

Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents Introduction FeaturesAbout This Guide OverviewInSpeed Technology Fibre Channel Arbitrated LoopInstallation Unpacking the SwitchInstalling the Switch Performing a Power On Systems Test Using Small Form Factor Pluggable SFP TransceiversSmall Form-Factor Pluggable SFP Installation Small Form-Factor Pluggable SFP RemovalAttaching Devices Setting Up the SwitchUnderstanding the Switch’s LEDs Power OnSystem LEDs Port LEDs System LEDs IndicationSFP Cascading with Non-Overlapping Zones Cascading SwitchesAcceptable Single Cascade in Zones 2-12 Only Using the Web Manager Connecting to the Web ManagerE rv i e w Logging On and Off NavigationConfiguring the Switch Configuration Task Location in Web ManagerResetting the Switch Setting Description System Information SettingsClick Change Settings Network SettingsSwitching Mode Switch SpeedSwitch Identification Blocking ARBTime Settings Downloading the Switch ConfigurationFirmware Information Firmware SettingsEvent Log Messages Click Change Firmware SettingsFC Switch Information FC Switch InformationDetection Indication OS InformationCLS 11.Ordered Set Information Page with Highlighted Zones Port Usage Information13.Received Port Utilization Page with Highlighted Zones Value Description15.Port Information Port Settings16.Port Information Page with Highlighted Zones 18.Cascade Information Mode Description19.Cascade Information Page with Highlighted Zones Switch Policy Description Policy Settings21.Policies Change Settings 22.Overlapping Zones Zone Settings25.Overlapping Zone 1 Information Overlapping ZonesNon-Overlapping Zones 26.Overlapping Zone 1 Information ConfigurationClick Back to Non-overlapping Zone Info to view the changes Management Connecting to the CLI Using the Command Line Interface CLINoz Configuration Task CLI CommandChanging the Switch’s IP Parameters Configuring Switch InformationEnabling or Disabling Dhcp Requests Downloading New Firmware Managing the FirmwareMessage Action Edit Trap Destination Menu Active Value NEW Value Configuring the Trap Destination TableOption Description Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy Description PoliciesThreshold Information Settings DescriptionAction Description ActionsCommand Description Changing the Switching ModeNumber. You can also change the port policies PLL Displaying PortsEnables you to configure control of the port. Select from Resetting the Hardware Resetting the SwitchResetting the Switch to Factory Default Settings Viewing the Event LogChanging the Switch’s Operating Speed Overlapping Zoning ConfigurationViewing and Understanding Zoning Information Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationTechnical Support ReferenceTro ub l e sh oo ti n g Fibre Channel References Small Form-Factor Pluggable SFP IssuesAppendixes Specification s Appendix a SpecificationsVixel Model 335 Operating Conditions Operating ConditionsConsole Commands CommandsGeneral Commands Browse CommandsShow Zone Action CommandsURL Event Meaning Action Severity Message Appendix C Event MessagesAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Index Configuring switch informationIndex

Related manuals

Manual 74 pages 62.9 Kb