Vixel 335 manual Configuration Task CLI Command, Noz

Page 40

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

Configuring the Switch

The CLI enables you to configure the switch settings, policies, and zoning.

A list of frequent switch configuration tasks and their commands is shown here. Refer to the provided page number for more detailed information on each configuration task.

Configuration Task	CLI Command

Change the IP parameters	co
(See “Changing the Switch’s IP Parameters” on page 38.)

Change switch identification, contact, location, etc.	si
(See “Configuring Switch Information” on page 38.)

Upgrade firmware	fw
(See “Managing the Firmware” on page 39.)

Add or delete a trap destination (through the	ct
Configuration menu)
(See “Configuring the Trap Destination Table” on page 41.)

Changing the password	pw

View switch management, policies, error thresholds, and	mc
other switch settings.
(See “Viewing Management, Policy, and Threshold Settings” on
page 43.)

Change the switching mode	sw
(See “Changing the Switching Mode” on page 47.)

Configure zoning	oz
(See “Viewing and Understanding Zoning Information” on	(for overlapping zoning)
page 52.)
	noz
	(for non-overlapping zoning)

Reset switch	rs
(See “Resetting the Switch” on page 13.)

Reset switch to factory default settings	rc
(See “Resetting the Switch to Factory Default Settings” on
page 51.)

View & modify port settings	po
(See “Displaying Ports” on page 49.)

Change the switch speed	lsp
(See “Changing the Switch’s Operating Speed” on page 52.)

View the event log	ev
(See “Viewing the Event Log” on page 51.)

To view the complete list of available switch commands while using the CLI, type ? or h at the prompt. For a complete listing of all CLI commands, see CLI CONSOLE COMMANDS (APPENDIX B) on page 60.

37

Image 40

Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents Features IntroductionAbout This Guide OverviewFibre Channel Arbitrated Loop InSpeed TechnologyUnpacking the Switch InstallationInstalling the Switch Using Small Form Factor Pluggable SFP Transceivers Performing a Power On Systems TestSmall Form-Factor Pluggable SFP Installation Small Form-Factor Pluggable SFP RemovalSetting Up the Switch Attaching DevicesPower On Understanding the Switch’s LEDsSystem LEDs System LEDs Indication Port LEDsSFP Cascading Switches Cascading with Non-Overlapping ZonesAcceptable Single Cascade in Zones 2-12 Only Connecting to the Web Manager Using the Web ManagerE rv i e w Navigation Logging On and OffConfiguration Task Location in Web Manager Configuring the SwitchResetting the Switch System Information Settings Setting DescriptionNetwork Settings Click Change SettingsSwitch Speed Switching ModeSwitch Identification Blocking ARBDownloading the Switch Configuration Time SettingsFirmware Settings Firmware InformationClick Change Firmware Settings Event Log MessagesFC Switch Information FC Switch InformationOS Information Detection IndicationCLS Port Usage Information 11.Ordered Set Information Page with Highlighted ZonesValue Description 13.Received Port Utilization Page with Highlighted ZonesPort Settings 15.Port Information16.Port Information Page with Highlighted Zones Mode Description 18.Cascade Information19.Cascade Information Page with Highlighted Zones Policy Settings Switch Policy Description21.Policies Change Settings Zone Settings 22.Overlapping ZonesOverlapping Zones 25.Overlapping Zone 1 Information26.Overlapping Zone 1 Information Configuration Non-Overlapping ZonesClick Back to Non-overlapping Zone Info to view the changes Management Using the Command Line Interface CLI Connecting to the CLIConfiguration Task CLI Command NozConfiguring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling Dhcp Requests Managing the Firmware Downloading New FirmwareMessage Action Configuring the Trap Destination Table Edit Trap Destination Menu Active Value NEW ValueOption Description Changing the CLI/Web Password Viewing Management, Policy, and Threshold SettingsPolicies Policy DescriptionSettings Description Threshold InformationActions Action DescriptionChanging the Switching Mode Command DescriptionNumber. You can also change the port policies Displaying Ports PLLEnables you to configure control of the port. Select from Resetting the Switch Resetting the HardwareResetting the Switch to Factory Default Settings Viewing the Event LogOverlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10Reference Technical SupportTro ub l e sh oo ti n g Small Form-Factor Pluggable SFP Issues Fibre Channel ReferencesAppendixes Appendix a Specifications Specification sOperating Conditions Vixel Model 335 Operating ConditionsCommands Console CommandsGeneral Commands Browse CommandsAction Commands Show ZoneURL Appendix C Event Messages Event Meaning Action Severity MessageAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Configuring switch information IndexIndex

Related manuals

Manual 74 pages 62.9 Kb