Vixel 335 manual Option Description

Page 45

Vixel Model 335 Installation & Configuration Guide

CHAPTER 3 Management

 

 

4.If you want to edit any of the listed options, type the number corresponding to the desired option (community [password], severity, state, or mode) and follow the prompts.

Option

Description

 

 

Community

Sets the community string to public or private. An SNMP server has a

 

"community string" which is like a password to get or set information.

 

Most devices have a "public" community string, which enables read-only

 

access to MIBs, as well as a "private" community string that enables you to

 

read and set certain parameters via SNMP. The community strings are

 

case-sensitive.

 

Options:

 

public

 

private

 

 

Severity

Select the severity level at which the traps become operational. The default

 

severity level is Warning.

 

Options:

 

0-Emergency

 

1-Alert

 

2-Critical

 

3-Error

 

4-Warning

 

5-Notice

 

6-Info

 

7-Debug

 

8-Mark

 

 

State

The state menu choice enables the trap to become active or inactive.

 

Options:

 

1-Destroy – the trap will be deleted from the table once changes are saved.

 

2-Inactive – the trap is not operational.

 

3-Active – the trap sends messages to the host identified in the IP Address

 

selection.

 

 

Mode

Determines whether the traps are accessed through the Event interface, the

 

Fibre Alliance interface, or both.

 

Options:

 

1-Event

 

3-FcMgmt

 

4-Both

 

 

5. Type 5 to save changes and exit.

The Trap Destination Table menu appears and displays your saved changes.

To edit a trap destination:

1.Enter the row number for the TRAP destination that you want to edit. The Edit Trap Destination Menu appears.

2.Type the number corresponding to the option (community [password], severity, state, or mode) you want to change and follow the prompts.

3.Type 5 to save changes and exit.

The Trap Destination Table menu appears and displays your saved changes.

To delete a trap destination:

1.Type 3 to select the Delete TRAP destination option.

2.Enter the row number that you want to delete.

The trap destination is deleted.

42

Image 45
Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents Introduction FeaturesAbout This Guide OverviewInSpeed Technology Fibre Channel Arbitrated LoopInstallation Unpacking the SwitchInstalling the Switch Performing a Power On Systems Test Using Small Form Factor Pluggable SFP TransceiversSmall Form-Factor Pluggable SFP Installation Small Form-Factor Pluggable SFP RemovalAttaching Devices Setting Up the SwitchUnderstanding the Switch’s LEDs Power OnSystem LEDs Port LEDs System LEDs IndicationSFP Cascading with Non-Overlapping Zones Cascading SwitchesAcceptable Single Cascade in Zones 2-12 Only Using the Web Manager Connecting to the Web ManagerE rv i e w Logging On and Off NavigationConfiguring the Switch Configuration Task Location in Web ManagerResetting the Switch Setting Description System Information SettingsClick Change Settings Network SettingsSwitching Mode Switch SpeedSwitch Identification Blocking ARBTime Settings Downloading the Switch ConfigurationFirmware Information Firmware SettingsEvent Log Messages Click Change Firmware SettingsFC Switch Information FC Switch InformationDetection Indication OS InformationCLS 11.Ordered Set Information Page with Highlighted Zones Port Usage Information13.Received Port Utilization Page with Highlighted Zones Value Description15.Port Information Port Settings16.Port Information Page with Highlighted Zones 18.Cascade Information Mode Description19.Cascade Information Page with Highlighted Zones Switch Policy Description Policy Settings21.Policies Change Settings 22.Overlapping Zones Zone Settings25.Overlapping Zone 1 Information Overlapping ZonesNon-Overlapping Zones 26.Overlapping Zone 1 Information ConfigurationClick Back to Non-overlapping Zone Info to view the changes Management Connecting to the CLI Using the Command Line Interface CLINoz Configuration Task CLI CommandChanging the Switch’s IP Parameters Configuring Switch InformationEnabling or Disabling Dhcp Requests Downloading New Firmware Managing the FirmwareMessage Action Edit Trap Destination Menu Active Value NEW Value Configuring the Trap Destination TableOption Description Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy Description PoliciesThreshold Information Settings DescriptionAction Description ActionsCommand Description Changing the Switching ModeNumber. You can also change the port policies PLL Displaying PortsEnables you to configure control of the port. Select from Resetting the Hardware Resetting the SwitchResetting the Switch to Factory Default Settings Viewing the Event LogChanging the Switch’s Operating Speed Overlapping Zoning ConfigurationViewing and Understanding Zoning Information Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationTechnical Support ReferenceTro ub l e sh oo ti n g Fibre Channel References Small Form-Factor Pluggable SFP IssuesAppendixes Specification s Appendix a SpecificationsVixel Model 335 Operating Conditions Operating ConditionsConsole Commands CommandsGeneral Commands Browse CommandsShow Zone Action CommandsURL Event Meaning Action Severity Message Appendix C Event MessagesAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Index Configuring switch informationIndex
Related manuals
Manual 74 pages 62.9 Kb