Vixel 335 manual E rv i e w, Using the Web Manager, Connecting to the Web Manager

Page 14

CHAPTER 3 Management

Overview 11

Using the Web Manager 11

Using the Command Line Interface (CLI) 36

O v e rv i e w

The switch utilizes both a Web Manager interface and a Command Line Interface (CLI) to manage the switch. You can change the switch’s device identification, upgrade firmware, configure switch settings and policies, define severity levels for event messages, and configure zoning.

Using the Web Manager

The Web Manager enables you to manage and monitor a switch from any network- connected computer. (Supported browsers are Netscape Navigator 4.7 or higher and Microsoft Internet Explorer 5.0 or higher. The browser needs to be Javascript-enabled.) With the Web Manager, you have the added benefits of easy navigation, simultaneous configuration of multiple ports, and named—rather than enumerated values within complex tables.

Connecting to the Web Manager

For a workstation to connect to the Web Manager, it must have access to the network on which the switch is connected.

If you need to verify the switch’s IP address, log into the switch’s command line interface through a serial link (see “Connecting to the CLI” on page 36).

To connect to the Web Manager:

1.Make sure the switch is connected to your network.

2.On a network-connected computer, open a web browser (such as Netscape Navigator or Microsoft Internet Explorer); in the URL text box, enter the switch’s address (DNS name or IP Address).

11

Image 14

Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents About This Guide FeaturesIntroduction OverviewFibre Channel Arbitrated Loop InSpeed TechnologyInstalling the Switch InstallationUnpacking the Switch Small Form-Factor Pluggable SFP Installation Using Small Form Factor Pluggable SFP TransceiversPerforming a Power On Systems Test Small Form-Factor Pluggable SFP RemovalSetting Up the Switch Attaching DevicesSystem LEDs Understanding the Switch’s LEDsPower On System LEDs Indication Port LEDsSFP Cascading Switches Cascading with Non-Overlapping ZonesAcceptable Single Cascade in Zones 2-12 Only E rv i e w Using the Web ManagerConnecting to the Web Manager Navigation Logging On and OffResetting the Switch Configuring the SwitchConfiguration Task Location in Web Manager System Information Settings Setting DescriptionNetwork Settings Click Change SettingsSwitch Identification Switch SpeedSwitching Mode Blocking ARBDownloading the Switch Configuration Time SettingsFirmware Settings Firmware InformationClick Change Firmware Settings Event Log MessagesFC Switch Information FC Switch InformationOS Information Detection IndicationCLS Port Usage Information 11.Ordered Set Information Page with Highlighted ZonesValue Description 13.Received Port Utilization Page with Highlighted ZonesPort Settings 15.Port Information16.Port Information Page with Highlighted Zones Mode Description 18.Cascade Information19.Cascade Information Page with Highlighted Zones Policy Settings Switch Policy Description21.Policies Change Settings Zone Settings 22.Overlapping ZonesOverlapping Zones 25.Overlapping Zone 1 Information26.Overlapping Zone 1 Information Configuration Non-Overlapping ZonesClick Back to Non-overlapping Zone Info to view the changes Management Using the Command Line Interface CLI Connecting to the CLIConfiguration Task CLI Command NozEnabling or Disabling Dhcp Requests Changing the Switch’s IP ParametersConfiguring Switch Information Managing the Firmware Downloading New FirmwareMessage Action Configuring the Trap Destination Table Edit Trap Destination Menu Active Value NEW ValueOption Description Changing the CLI/Web Password Viewing Management, Policy, and Threshold SettingsPolicies Policy DescriptionSettings Description Threshold InformationActions Action DescriptionChanging the Switching Mode Command DescriptionNumber. You can also change the port policies Displaying Ports PLLEnables you to configure control of the port. Select from Resetting the Switch to Factory Default Settings Resetting the SwitchResetting the Hardware Viewing the Event LogViewing and Understanding Zoning Information Changing the Switch’s Operating SpeedOverlapping Zoning Configuration Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10Reference Technical SupportTro ub l e sh oo ti n g Small Form-Factor Pluggable SFP Issues Fibre Channel ReferencesAppendixes Appendix a Specifications Specification sOperating Conditions Vixel Model 335 Operating ConditionsGeneral Commands CommandsConsole Commands Browse CommandsAction Commands Show ZoneURL Appendix C Event Messages Event Meaning Action Severity MessageAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Configuring switch information IndexIndex

Related manuals

Manual 74 pages 62.9 Kb