Vixel 335 manual Message Action

Page 43

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

Note: To cancel out of the file transfer facility, press CTRL+X several times.

d.Type the following and press Enter. quit

4.In the terminal session window, type 1 to verify and store the new firmware. The following message appears.

Clearing backup host filename.. Clearing backup host IP address.. Verifying file integrity.. Erasing flash memory.. Programming flash memory.. Verifying..

*PROGRAM LOAD SUCCESSFUL*

Type fw, then type 1.

The active and alternate firmware versions are displayed.

5.If the “alternate version” is anything other than the firmware you just downloaded, verify that the file is good and repeat the download.

6.If you want to activate the alternate version (the newly downloaded firmware):

a.Type 2 to select the alternate version for execution on the next boot cycle.

b.Type 1 to verify that the following message is displayed under the firmware versions: “Note: ALTERNATE selected for execution on next boot cycle.” (If this message is not displayed, repeat steps a and b to toggle back.)

c.Type 5 to reboot.

The management agent disconnects, reboots, and activates the downloaded firmware. The “Disconnecting and Rebooting” message appears.

The firmware is downloaded.

Serial Method (Menu Option 4)

The Serial method for downloading firmware is available for Windows only.

1.Ensure that the switch and workstation are connected through a serial null modem cable.

2.Type 4.

The file transfer facility appears.

3.Choose Send File from the Transfer pull-down menu in HyperTerminal. The Send File dialog box appears.

4.Type (or browse for) the filename, select “1K Xmodem” from the Protocol drop- down list, and click Send.

A status message appears.

5.If the status message says anything other than “File transfer completed,” perform the action recommended for the appropriate message shown below.

Message	Action

CRC Error	Try another file. The file you are attempting to download may be corrupted.

Time out error	Cycle power to the switch and retry the download procedure.

Access denied	Close and reestablish the connection. Cycle power to the switch and retry the
	download procedure.

40

Image 43

Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents Overview FeaturesIntroduction About This GuideInSpeed Technology Fibre Channel Arbitrated LoopUnpacking the Switch InstallationInstalling the Switch Small Form-Factor Pluggable SFP Removal Using Small Form Factor Pluggable SFP TransceiversPerforming a Power On Systems Test Small Form-Factor Pluggable SFP InstallationAttaching Devices Setting Up the SwitchPower On Understanding the Switch’s LEDsSystem LEDs Port LEDs System LEDs IndicationSFP Cascading with Non-Overlapping Zones Cascading SwitchesAcceptable Single Cascade in Zones 2-12 Only Connecting to the Web Manager Using the Web ManagerE rv i e w Logging On and Off NavigationConfiguration Task Location in Web Manager Configuring the SwitchResetting the Switch Setting Description System Information SettingsClick Change Settings Network SettingsBlocking ARB Switch SpeedSwitching Mode Switch IdentificationTime Settings Downloading the Switch ConfigurationFirmware Information Firmware SettingsEvent Log Messages Click Change Firmware SettingsFC Switch Information FC Switch InformationDetection Indication OS InformationCLS 11.Ordered Set Information Page with Highlighted Zones Port Usage Information13.Received Port Utilization Page with Highlighted Zones Value Description15.Port Information Port Settings16.Port Information Page with Highlighted Zones 18.Cascade Information Mode Description19.Cascade Information Page with Highlighted Zones Switch Policy Description Policy Settings21.Policies Change Settings 22.Overlapping Zones Zone Settings25.Overlapping Zone 1 Information Overlapping ZonesNon-Overlapping Zones 26.Overlapping Zone 1 Information ConfigurationClick Back to Non-overlapping Zone Info to view the changes Management Connecting to the CLI Using the Command Line Interface CLINoz Configuration Task CLI CommandConfiguring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling Dhcp Requests Downloading New Firmware Managing the FirmwareMessage Action Edit Trap Destination Menu Active Value NEW Value Configuring the Trap Destination TableOption Description Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy Description PoliciesThreshold Information Settings DescriptionAction Description ActionsCommand Description Changing the Switching ModeNumber. You can also change the port policies PLL Displaying PortsEnables you to configure control of the port. Select from Viewing the Event Log Resetting the SwitchResetting the Hardware Resetting the Switch to Factory Default SettingsOverlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationTechnical Support ReferenceTro ub l e sh oo ti n g Fibre Channel References Small Form-Factor Pluggable SFP IssuesAppendixes Specification s Appendix a SpecificationsVixel Model 335 Operating Conditions Operating ConditionsBrowse Commands CommandsConsole Commands General CommandsShow Zone Action CommandsURL Event Meaning Action Severity Message Appendix C Event MessagesAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Index Configuring switch informationIndex

Related manuals

Manual 74 pages 62.9 Kb