Vixel 335 manual Using the Command Line Interface CLI, Connecting to the CLI

Page 39

Vixel Model 335 Installation & Configuration Guide

CHAPTER 3 Management

 

 

Using the Command Line Interface (CLI)

The Command Line Interface (CLI) allows you to complete several switch management tasks over Ethernet through a telnet session or through a direct serial link. While both the CLI and Web Manager interfaces allow you to view switch information and configure switch settings, the CLI also allows you to enable or disable DHCP requests, change the CLI/Web Manager password, manage traps, and complete several other switch management functions.

Note: You may have up to 10 concurrent telnet sessions accessing the switch.

Connecting to the CLI

You can connect to the CLI over the telnet interface or the serial link interface.

To connect over Ethernet through telnet interface:

1.Make sure the Vixel Managed Switch is connected to an Ethernet network via the switch’s Ethernet connection and that the monitoring workstation can access this Ethernet network.

2.Make sure that you know the switch’s IP address before connecting to the CLI. (the default IP Address is 0.0.0.0)

3.At a command line prompt, type telnet IP (where IP is the switch’s IP address). You are now connected to the CLI and ready to log on.

To connect through a serial link:

1.Attach one end of an RS-232 null modem cable to the serial port on the workstation; attach the other end to the RS-232 port on the switch.

2.For Unix workstations, type the following command at a Unix prompt (where SerialPortDevicePath is the filepath to the serial port used for connection): cu -s 19200 -b 8 -1 SerialPortDevicePath

3.For Windows® platforms, open a terminal session through a terminal emulation program (such as HyperTerminal) with the appropriate serial port (for example, COM1) and the following serial port parameters:

Bits per second: 19200

Data bits: 8

Parity: None

Stop bits: 1

Flow control: Xon/Xoff

You are now connected to the CLI and ready to log on.

Logging On and Off

To log onto the CLI (once connected as shown above), type li at the prompt, then type the password (the default password is password).

To log off the CLI, type lo at the prompt.

Make sure you change the password after you log on the first time.

36

Image 39
Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents Overview FeaturesIntroduction About This GuideInSpeed Technology Fibre Channel Arbitrated LoopInstallation Unpacking the SwitchInstalling the Switch Small Form-Factor Pluggable SFP Removal Using Small Form Factor Pluggable SFP TransceiversPerforming a Power On Systems Test Small Form-Factor Pluggable SFP InstallationAttaching Devices Setting Up the SwitchUnderstanding the Switch’s LEDs Power OnSystem LEDs Port LEDs System LEDs IndicationSFP Cascading with Non-Overlapping Zones Cascading SwitchesAcceptable Single Cascade in Zones 2-12 Only Using the Web Manager Connecting to the Web ManagerE rv i e w Logging On and Off NavigationConfiguring the Switch Configuration Task Location in Web ManagerResetting the Switch Setting Description System Information SettingsClick Change Settings Network SettingsBlocking ARB Switch SpeedSwitching Mode Switch IdentificationTime Settings Downloading the Switch ConfigurationFirmware Information Firmware SettingsEvent Log Messages Click Change Firmware SettingsFC Switch Information FC Switch InformationDetection Indication OS InformationCLS 11.Ordered Set Information Page with Highlighted Zones Port Usage Information13.Received Port Utilization Page with Highlighted Zones Value Description15.Port Information Port Settings16.Port Information Page with Highlighted Zones 18.Cascade Information Mode Description19.Cascade Information Page with Highlighted Zones Switch Policy Description Policy Settings21.Policies Change Settings 22.Overlapping Zones Zone Settings25.Overlapping Zone 1 Information Overlapping ZonesNon-Overlapping Zones 26.Overlapping Zone 1 Information ConfigurationClick Back to Non-overlapping Zone Info to view the changes Management Connecting to the CLI Using the Command Line Interface CLINoz Configuration Task CLI CommandChanging the Switch’s IP Parameters Configuring Switch InformationEnabling or Disabling Dhcp Requests Downloading New Firmware Managing the FirmwareMessage Action Edit Trap Destination Menu Active Value NEW Value Configuring the Trap Destination TableOption Description Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy Description PoliciesThreshold Information Settings DescriptionAction Description ActionsCommand Description Changing the Switching ModeNumber. You can also change the port policies PLL Displaying PortsEnables you to configure control of the port. Select from Viewing the Event Log Resetting the SwitchResetting the Hardware Resetting the Switch to Factory Default SettingsChanging the Switch’s Operating Speed Overlapping Zoning ConfigurationViewing and Understanding Zoning Information Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationTechnical Support ReferenceTro ub l e sh oo ti n g Fibre Channel References Small Form-Factor Pluggable SFP IssuesAppendixes Specification s Appendix a SpecificationsVixel Model 335 Operating Conditions Operating ConditionsBrowse Commands CommandsConsole Commands General CommandsShow Zone Action CommandsURL Event Meaning Action Severity Message Appendix C Event MessagesAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Index Configuring switch informationIndex
Related manuals
Manual 74 pages 62.9 Kb