Vixel 335 manual Port Settings, Port Information

Page 28

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

3.Click Submit to accept the changes.

4.Click Back to Port Usage to view the new settings.

Port Settings

The Port Information page displays the port status for each port on the switch.

To view the port settings, click Port. The Port Information page appears.

Figure 3-15.Port Information Page

The displayed settings are listed below:

Setting	Description

Port	The actual port on the switch.

Transceiver	The type of transceiver inserted in the port.

Trcvr LED	If a transceiver is inserted properly, the LED is on.

Fault LED	The port is bypassed due to a problem detected by either the
	transceiver’s transmit logic or the SFP transceiver itself.
	Transceiver problems include unconnected fiber, remote node
	not transmitting, LIP(F8), or a faulty transceiver.

State	The current state of the selected port.

TX	The state of the transmitter on the selected port.

Inserts	The number of times a transceiver has been inserted into the
	port since the last switch reset.

Freq	The port locked in on the communicating frequency for which
	the switch is configured.

Zone	The zone in which the port is located.

Cascade Mode	Displays the cascade mode for the specified port.

Cascade State	Displays the cascade state for the specified port.

25

Image 28

Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents Features IntroductionAbout This Guide OverviewFibre Channel Arbitrated Loop InSpeed TechnologyUnpacking the Switch InstallationInstalling the Switch Using Small Form Factor Pluggable SFP Transceivers Performing a Power On Systems TestSmall Form-Factor Pluggable SFP Installation Small Form-Factor Pluggable SFP RemovalSetting Up the Switch Attaching DevicesPower On Understanding the Switch’s LEDsSystem LEDs System LEDs Indication Port LEDsSFP Cascading Switches Cascading with Non-Overlapping ZonesAcceptable Single Cascade in Zones 2-12 Only Connecting to the Web Manager Using the Web ManagerE rv i e w Navigation Logging On and OffConfiguration Task Location in Web Manager Configuring the SwitchResetting the Switch System Information Settings Setting DescriptionNetwork Settings Click Change SettingsSwitch Speed Switching ModeSwitch Identification Blocking ARBDownloading the Switch Configuration Time SettingsFirmware Settings Firmware InformationClick Change Firmware Settings Event Log MessagesFC Switch Information FC Switch InformationOS Information Detection IndicationCLS Port Usage Information 11.Ordered Set Information Page with Highlighted ZonesValue Description 13.Received Port Utilization Page with Highlighted ZonesPort Settings 15.Port Information16.Port Information Page with Highlighted Zones Mode Description 18.Cascade Information19.Cascade Information Page with Highlighted Zones Policy Settings Switch Policy Description21.Policies Change Settings Zone Settings 22.Overlapping ZonesOverlapping Zones 25.Overlapping Zone 1 Information26.Overlapping Zone 1 Information Configuration Non-Overlapping ZonesClick Back to Non-overlapping Zone Info to view the changes Management Using the Command Line Interface CLI Connecting to the CLIConfiguration Task CLI Command NozConfiguring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling Dhcp Requests Managing the Firmware Downloading New FirmwareMessage Action Configuring the Trap Destination Table Edit Trap Destination Menu Active Value NEW ValueOption Description Changing the CLI/Web Password Viewing Management, Policy, and Threshold SettingsPolicies Policy DescriptionSettings Description Threshold InformationActions Action DescriptionChanging the Switching Mode Command DescriptionNumber. You can also change the port policies Displaying Ports PLLEnables you to configure control of the port. Select from Resetting the Switch Resetting the HardwareResetting the Switch to Factory Default Settings Viewing the Event LogOverlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10Reference Technical SupportTro ub l e sh oo ti n g Small Form-Factor Pluggable SFP Issues Fibre Channel ReferencesAppendixes Appendix a Specifications Specification sOperating Conditions Vixel Model 335 Operating ConditionsCommands Console CommandsGeneral Commands Browse CommandsAction Commands Show ZoneURL Appendix C Event Messages Event Meaning Action Severity MessageAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Configuring switch information IndexIndex

Related manuals

Manual 74 pages 62.9 Kb