Vixel 335 manual Sfp

Page 11

Vixel Model 335 Installation & Configuration Guide

CHAPTER 2 Installation

 

 

An explanation of the Port LED indicators is listed below:

SFP

Port

 

Bypassed/

 

Status

Indication

Activity

LED

 

LED

 

 

 

 

 

 

Off

Off

Normal status of operation for ports in which SFPs

 

 

are not installed.

 

 

The port will be in the bypass state, which precludes

 

 

the port from participating in the network.

 

 

 

On

Off

Normal operation. Port and device are operational.

 

 

 

On

On

Bypass. The port is non-operational due to loss of

 

(Yellow)

signal, poor signal integrity, or the attached node is

 

 

sending LIP(F8,xx).

 

 

This is the normal status condition when the SFP is

 

 

present but not attached to a FC-AL node, or if it is

 

 

only attached to a cable assembly with nothing

 

 

attached at the opposite end. Replacing such a port

 

 

(or replugging the same port twice) is considered to

 

 

be a configuration change, which should initiate the

 

 

Loop Initialization Procedure by the attached device.

 

 

 

Off

On

Tx Fault. The port is non-operational due to an SFP

 

(Yellow)

transmitter fault or improperly-seated SFP.

 

 

 

Off

Blinking

The port is being manually controlled by a

 

(Yellow)

management entity.

 

 

 

Blinking

Blinking

A management entity is forcing a port beacon to

 

(Yellow)

locate a particular port on the switch.

 

 

 

On

On

A connection has been made with the port.

 

(Green)

Note: This LED is only applicable when the port is

 

 

operating in switching mode. If the port is in

 

 

switching mode and the LED is off, the port is not

 

 

currently involved in a transaction.

 

 

 

8

Image 11
Contents InSpeed Model Part Number 00041363-001 Rev. a Table of Contents Overview FeaturesIntroduction About This GuideInSpeed Technology Fibre Channel Arbitrated LoopInstalling the Switch InstallationUnpacking the Switch Small Form-Factor Pluggable SFP Removal Using Small Form Factor Pluggable SFP TransceiversPerforming a Power On Systems Test Small Form-Factor Pluggable SFP InstallationAttaching Devices Setting Up the SwitchSystem LEDs Understanding the Switch’s LEDsPower On Port LEDs System LEDs IndicationSFP Cascading with Non-Overlapping Zones Cascading SwitchesAcceptable Single Cascade in Zones 2-12 Only E rv i e w Using the Web ManagerConnecting to the Web Manager Logging On and Off NavigationResetting the Switch Configuring the SwitchConfiguration Task Location in Web Manager Setting Description System Information SettingsClick Change Settings Network SettingsBlocking ARB Switch SpeedSwitching Mode Switch IdentificationTime Settings Downloading the Switch ConfigurationFirmware Information Firmware SettingsEvent Log Messages Click Change Firmware SettingsFC Switch Information FC Switch InformationDetection Indication OS InformationCLS 11.Ordered Set Information Page with Highlighted Zones Port Usage Information13.Received Port Utilization Page with Highlighted Zones Value Description15.Port Information Port Settings16.Port Information Page with Highlighted Zones 18.Cascade Information Mode Description19.Cascade Information Page with Highlighted Zones Switch Policy Description Policy Settings21.Policies Change Settings 22.Overlapping Zones Zone Settings25.Overlapping Zone 1 Information Overlapping ZonesNon-Overlapping Zones 26.Overlapping Zone 1 Information ConfigurationClick Back to Non-overlapping Zone Info to view the changes Management Connecting to the CLI Using the Command Line Interface CLINoz Configuration Task CLI CommandEnabling or Disabling Dhcp Requests Changing the Switch’s IP ParametersConfiguring Switch Information Downloading New Firmware Managing the FirmwareMessage Action Edit Trap Destination Menu Active Value NEW Value Configuring the Trap Destination TableOption Description Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy Description PoliciesThreshold Information Settings DescriptionAction Description ActionsCommand Description Changing the Switching ModeNumber. You can also change the port policies PLL Displaying PortsEnables you to configure control of the port. Select from Viewing the Event Log Resetting the SwitchResetting the Hardware Resetting the Switch to Factory Default SettingsViewing and Understanding Zoning Information Changing the Switch’s Operating SpeedOverlapping Zoning Configuration Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationTechnical Support ReferenceTro ub l e sh oo ti n g Fibre Channel References Small Form-Factor Pluggable SFP IssuesAppendixes Specification s Appendix a SpecificationsVixel Model 335 Operating Conditions Operating ConditionsBrowse Commands CommandsConsole Commands General CommandsShow Zone Action CommandsURL Event Meaning Action Severity Message Appendix C Event MessagesAppendix C Event Messages Vixel Model 335 Installation & Configuration Guide Vixel Model 335 Installation & Configuration Guide Cross References Appendix E Glossary Scsi Index Configuring switch informationIndex
Related manuals
Manual 74 pages 62.9 Kb